If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
ADI1984A chipset audio output power
How much audio power can an onboard chipset handle?
I'm considering purchase of a Dell T3500 Precision Workstation, and I don't need anything more than 2 channels of stereo. I'm also considering the M-Audio Studiophile AV 40 speakers, each of which the specs say can output 20 watts of audio power. This means that if I use the motherboard's ADI1984A integrated audio chipset, the chips would have to handle a total of 40 watts of power. Are they capable of doing that without appreciable distortion? Or would I need to use an audio card of some sort (or powered speakers) for that amount of audio power? *TimDaniels* |
#2
|
|||
|
|||
ADI1984A chipset audio output power
"Timothy Daniels" NoSpam SpamMeKnot.biz wrote:
How much audio power can an onboard chipset handle? I'm considering purchase of a Dell T3500 Precision Workstation, and I don't need anything more than 2 channels of stereo. I'm also considering the M-Audio Studiophile AV 40 speakers, each of which the specs say can output 20 watts of audio power. This means that if I use the motherboard's ADI1984A integrated audio chipset, the chips would have to handle a total of 40 watts of power. Are they capable of doing that No. without appreciable distortion? Or would I need to use an audio card of some sort (or powered speakers) for that amount of audio power? Buy powered speakers, unless you want to buy a discrete (standalone) power amplifier. Onboard audio chipsets do not include power amplifiers. And the days of amplified sound cards are long gone. -- *TimDaniels* |
#3
|
|||
|
|||
ADI1984A chipset audio output power
Timothy Daniels wrote:
How much audio power can an onboard chipset handle? I'm considering purchase of a Dell T3500 Precision Workstation, and I don't need anything more than 2 channels of stereo. I'm also considering the M-Audio Studiophile AV 40 speakers, each of which the specs say can output 20 watts of audio power. This means that if I use the motherboard's ADI1984A integrated audio chipset, the chips would have to handle a total of 40 watts of power. Are they capable of doing that without appreciable distortion? Or would I need to use an audio card of some sort (or powered speakers) for that amount of audio power? *TimDaniels* The speakers have built-in amplifiers. No "power" of note, will be drawn from the computer. http://www.m-audio.com/products/en_u...phileAV40.html "20-watt-per-channel amplifier with Class A/B architecture" That means the speakers take care of all "power" issues, because there is an amplifier inside the speakers. From the specifications tab on that web page: "input Connectors: left and right RCA line input, left and right 1/4" TRS input and 1/8" aux input input Impedance: 10 k ohm unbalanced, 20 k ohm balanced Computer audio outputs have two specifications. If you find three to six 1/8" stereo connectors on the back of a computer, the one labeled "Line Out" can drive a 32 ohm load. The other channels can drive a 600 ohm load. Computer "line level", means being able to drive somewhere around 1 volt RMS into a 600 or 32 ohm load. The connector (or connectors) that support 32 ohm loads, are intended to drive headphones. Usually, there are limits as to how many sets of headphones the built-in computer audio can drive. The input impedance of the amplifiers in those speakers, have 10,000 ohms or higher value. Higher resistance draws less power. So comparing 10,000 ohms input, to 600 or 32 ohms output, is no contest. The computer can barely feel the electrical load of those speakers. You could drive a ton of amplified speakers in parallel, because of the high input impedance. So you'll have no problem at all using those speakers. "Amplified" speakers, are intended for usage with your average computer. There is a power switch, and a line cord connector on the back of the left speaker. A regular speaker cable runs from the left speaker to the right speaker. The stereo amplifier is contained inside the left speaker, and that stereo amp drives the right speaker. A cable is needed, to connect the right speaker to its amplifier. http://www.m-audio.com/images/global...PAV40_back.jpg I suspect the "Aux-In" on the front of the speakers, is where you run a cable from the "Line Out" on your computer. That is the most convenient way of connecting it. Alternately, you can use a 1/8" to dual RCA adapter, if you want to use the RCA inputs on the back of the left speaker. http://www.m-audio.com/images/global...AV40_front.jpg You can see a volume control, on the left speaker, in the lower left hand corner. It is lighted, so you can find it in the dark. The product comes with all cables, and appears to be ready to use, out of the box. Set the AC input to 120 or 220, plug in the AC cable, flip on the "Power" switch, set the volume knob on the front to a comfortable level, and enjoy. HTH, Paul |
#4
|
|||
|
|||
ADI1984A chipset audio output power
"Paul" wrote:
Timothy Daniels wrote: How much audio power can an onboard chipset handle? I'm considering purchase of a Dell T3500 Precision Workstation, and I don't need anything more than 2 channels of stereo. I'm also considering the M-Audio Studiophile AV 40 speakers, each of which the specs say can output 20 watts of audio power. This means that if I use the motherboard's ADI1984A integrated audio chipset, the chips would have to handle a total of 40 watts of power. Are they capable of doing that without appreciable distortion? Or would I need to use an audio card of some sort (or powered speakers) for that amount of audio power? *TimDaniels* The speakers have built-in amplifiers. No "power" of note, will be drawn from the computer. http://www.m-audio.com/products/en_u...phileAV40.html "20-watt-per-channel amplifier with Class A/B architecture" That means the speakers take care of all "power" issues, because there is an amplifier inside the speakers. From the specifications tab on that web page: "input Connectors: left and right RCA line input, left and right 1/4" TRS input and 1/8" aux input input Impedance: 10 k ohm unbalanced, 20 k ohm balanced Computer audio outputs have two specifications. If you find three to six 1/8" stereo connectors on the back of a computer, the one labeled "Line Out" can drive a 32 ohm load. The other channels can drive a 600 ohm load. Computer "line level", means being able to drive somewhere around 1 volt RMS into a 600 or 32 ohm load. The connector (or connectors) that support 32 ohm loads, are intended to drive headphones. Usually, there are limits as to how many sets of headphones the built-in computer audio can drive. The input impedance of the amplifiers in those speakers, have 10,000 ohms or higher value. Higher resistance draws less power. So comparing 10,000 ohms input, to 600 or 32 ohms output, is no contest. The computer can barely feel the electrical load of those speakers. You could drive a ton of amplified speakers in parallel, because of the high input impedance. So you'll have no problem at all using those speakers. "Amplified" speakers, are intended for usage with your average computer. There is a power switch, and a line cord connector on the back of the left speaker. A regular speaker cable runs from the left speaker to the right speaker. The stereo amplifier is contained inside the left speaker, and that stereo amp drives the right speaker. A cable is needed, to connect the right speaker to its amplifier. http://www.m-audio.com/images/global...PAV40_back.jpg I suspect the "Aux-In" on the front of the speakers, is where you run a cable from the "Line Out" on your computer. That is the most convenient way of connecting it. Alternately, you can use a 1/8" to dual RCA adapter, if you want to use the RCA inputs on the back of the left speaker. http://www.m-audio.com/images/global...AV40_front.jpg You can see a volume control, on the left speaker, in the lower left hand corner. It is lighted, so you can find it in the dark. The product comes with all cables, and appears to be ready to use, out of the box. Set the AC input to 120 or 220, plug in the AC cable, flip on the "Power" switch, set the volume knob on the front to a comfortable level, and enjoy. HTH, Paul Thanks, Paul and John. I suspected that the chipset would only supply the audio signal power, not the audio output power that drove the speakers. But the Dell sales rep kept insisting that the workstation's audio chipset could handle an output of 20watts per channel easily, and he even said that he'd send me an audio card if I found that it didn't. Somehow, I couldn't see that kind of signal power coming off the motherboard, so I figured it would be prudent to check in the NGs. Thanks, again, guys. *TimDaniels* |
#5
|
|||
|
|||
ADI1984A chipset audio output power
Hi!
How much audio power can an onboard chipset handle? It's a line level output only, at best. It will drive small speakers or possibly headphones. I doubt you'd damage the audio hardware, but it won't sound like much of anything at all trying to drive those speakers. If they are not powered, I'd highly recommend using something like the Sherwood RX-4109 or 4105 stereo receivers to drive them. They're cheap and sound good. William |
#6
|
|||
|
|||
ADI1984A chipset audio output power
"William R. Walsh" replied:
Hi! How much audio power can an onboard chipset handle? It's a line level output only, at best. It will drive small speakers or possibly headphones. I doubt you'd damage the audio hardware, but it won't sound like much of anything at all trying to drive those speakers. If they are not powered, I'd highly recommend using something like the Sherwood RX-4109 or 4105 stereo receivers to drive them. They're cheap and sound good. William Thanks, William. I've decided on the M-Audio AV40s, which are powered speakers. I've spent 2 weeks agonizing over so many options that adding selection of an external amplifier and passive speakers would have tripped my circuit breakers. :-) These speakers don't have a bass box, but they are big and heavy, and I figure they'll be good enough for casual listening in 2-channel stereo. *TimDaniels* |
#7
|
|||
|
|||
ADI1984A chipset audio output power
"Timothy Daniels" wrote in
m: "William R. Walsh" replied: Hi! How much audio power can an onboard chipset handle? It's a line level output only, at best. It will drive small speakers or possibly headphones. I doubt you'd damage the audio hardware, but it won't sound like much of anything at all trying to drive those speakers. If they are not powered, I'd highly recommend using something like the Sherwood RX-4109 or 4105 stereo receivers to drive them. They're cheap and sound good. William Thanks, William. I've decided on the M-Audio AV40s, which are powered speakers. I've spent 2 weeks agonizing over so many options that adding selection of an external amplifier and passive speakers would have tripped my circuit breakers. :-) These speakers don't have a bass box, but they are big and heavy, and I figure they'll be good enough for casual listening in 2-channel stereo. *TimDaniels* Hi, I am also looking for a pair of 2.0 speakers to listen to music. The reviews for the AV40s are better than average. Have you gotten these yet? Boris |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
audio output on dell 1520 | Peter[_4_] | Dell Computers | 0 | August 4th 07 03:23 AM |
How make audio output mono | David Peters (UK) | General | 14 | April 12th 06 04:21 PM |
Which current GF cards use external TV output chipset? | Larry L. | Nvidia Videocards | 5 | May 26th 04 03:51 AM |
Audio input+output at the same time | Uwe Lauth | PC Soundcards | 0 | October 1st 03 07:26 PM |
What's the optical audio output all about? | Joe Woods | Gigabyte Motherboards | 2 | August 2nd 03 09:02 PM |