If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
TV-out stopped working
Hi ng
I own a Radeon 9600 XT with a tv-out, which I use to watch avi-movies on my TV. However, when I installed Windows XP service pack 2 and updated my ATI driver to the latest Catalyst, suddenly my TV can't be detected. When I to "ATI display settings", "Advanced", Diplay tab, I can't activate my TV. I checked the cables, and the TV's on. Any solution, other than formatting and reinstalling all over? TIA |
#2
|
|||
|
|||
"Dr.John" wrote in message ... Hi ng I own a Radeon 9600 XT with a tv-out, which I use to watch avi-movies on my TV. However, when I installed Windows XP service pack 2 and updated my ATI driver to the latest Catalyst, suddenly my TV can't be detected. When I to "ATI display settings", "Advanced", Diplay tab, I can't activate my TV. I checked the cables, and the TV's on. Any solution, other than formatting and reinstalling all over? TIA Try to use the Force-Detection option in the troubleshooting section of the Catalysts.This has been a common problem with many ATI cards but it's nothing serious. |
#3
|
|||
|
|||
"Glitch" wrote in message ... "Dr.John" wrote in message ... Hi ng I own a Radeon 9600 XT with a tv-out, which I use to watch avi-movies on my TV. However, when I installed Windows XP service pack 2 and updated my ATI driver to the latest Catalyst, suddenly my TV can't be detected. When I to "ATI display settings", "Advanced", Diplay tab, I can't activate my TV. I checked the cables, and the TV's on. Any solution, other than formatting and reinstalling all over? TIA Try to use the Force-Detection option in the troubleshooting section of the Catalysts.This has been a common problem with many ATI cards but it's nothing serious. Thanks for the quick reply. Still doesn't work. In the Catalyst Control Center, I'm choosing "Force TV detection", and then in the Displays manager, whenever I press "Detect Displays" or if I press the number two display box, I'm asked if I wish to enable display, but nothing happens. |
#4
|
|||
|
|||
"Dr.John" wrote in message
... "Glitch" wrote in message ... "Dr.John" wrote in message ... Hi ng I own a Radeon 9600 XT with a tv-out, which I use to watch avi-movies on my TV. However, when I installed Windows XP service pack 2 and updated my ATI driver to the latest Catalyst, suddenly my TV can't be detected. When I to "ATI display settings", "Advanced", Diplay tab, I can't activate my TV. I checked the cables, and the TV's on. Any solution, other than formatting and reinstalling all over? TIA Try to use the Force-Detection option in the troubleshooting section of the Catalysts.This has been a common problem with many ATI cards but it's nothing serious. Thanks for the quick reply. Still doesn't work. In the Catalyst Control Center, I'm choosing "Force TV detection", and then in the Displays manager, whenever I press "Detect Displays" or if I press the number two display box, I'm asked if I wish to enable display, but nothing happens. What happens if you disconnect your PC monitor and boot up with only the TV connected? Also, have you tried uninstalling the Control Center and instead opt for the more conventional ATI Control Panel and enable the displays from it? -- Robert J. Salvi, Ambiance Acoustics http://www.ambianceacoustics.com San Diego, CA USA (858) 485-7514 |
#5
|
|||
|
|||
Hi ng
I own a Radeon 9600 XT with a tv-out, which I use to watch avi-movies on my TV. However, when I installed Windows XP service pack 2 and updated my ATI driver to the latest Catalyst, suddenly my TV can't be detected. When I to "ATI display settings", "Advanced", Diplay tab, I can't activate my TV. I checked the cables, and the TV's on. Any solution, other than formatting and reinstalling all over? TIA What happens if you disconnect your PC monitor and boot up with only the TV connected? Also, have you tried uninstalling the Control Center and instead opt for the more conventional ATI Control Panel and enable the displays from it? Thanks for the reply Nothing happened when I boot up with only the TV. After uninstalling the Control Center I can now force detection of my TV and get a nice picture, but when I play AVI-movies I get a black screen on the TV, but it looks normal on the monitor. How do I correct this, so that I can watch the movie on my TV? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
P4P800-E Deluxe all USB ports stopped working?? Help! | jlcarriere | Asus Motherboards | 4 | January 17th 05 12:25 AM |
Graphics card fan stopped working | Schism | General | 6 | July 23rd 04 10:51 PM |
Keyboard stopped working | News Groupie | General | 0 | May 2nd 04 10:38 AM |
FPS Really LOW - Whats Wrong? | John W. | Ati Videocards | 5 | January 20th 04 08:09 AM |
Radeon 9500 Pro suddenly stopped working! | Nordin | Ati Videocards | 4 | June 26th 03 09:40 AM |