A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » General Hardware & Peripherals » Homebuilt PC's
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

No ROM PCI IRQ routing table found: what does it mean ?



 
 
Thread Tools Display Modes
  #1  
Old December 2nd 04, 04:59 PM
claude
external usenet poster
 
Posts: n/a
Default No ROM PCI IRQ routing table found: what does it mean ?

I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
the following message:

"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"

Does anyone have an idea about it ?

Thanks for you help

Claude

PS: Please find the complete results of the tests (displayed in a DOS
window):

Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
1996-2004a.

PCI BIOS Version 2.10 found!
Number of PCI Busses : 1
PCI Characteristics : Config Mechanism 1

Searching for PCI Devices using the System BIOS

Vendor 8086h Intel Corporation
Device 7100h 82439TX 430TX System Controller
Command 0006h (Memory Access, BusMaster)
Status 2200h (Received Master Abort, Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Vendor 8086h Intel Corporation
Device 7110h 82371AB PIIX4 ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA

Vendor 8086h Intel Corporation
Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Address 4 is an I/O Port : 0000FFA0h

Vendor 8086h Intel Corporation
Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Address 4 is an I/O Port : 0000DB00h
System IRQ 3, INT# D

Vendor 8086h Intel Corporation
Device 7113h 82371AB PIIX4 Power Management Controller
Command 0003h (I/O Access, Memory Access)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other

Vendor 1002h ATI Technologies
Device 4755h Rage 3D II+ [Mach64 GTB]
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 9Ah, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
Subsystem Vendor 1002h ATI Technologies
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
Address 1 is an I/O Port : 0000DE00h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
Expansion ROM of 0Kb decoded by this card

Vendor 10ECh Realtek Semiconductor
Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
Command 0105h (I/O Access, BusMaster, System Errors)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
Medium Timing)
Revision 10h, Header Type 00h, Bus Latency 80h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
Subsystem Vendor 1799h Belkin Research and Development Labs
Address 0 is an I/O Port : 0000DC00h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
System IRQ 11, INT# A
Expansion ROM of 0Kb decoded by this card
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# from mode(s) D1, D2, D3hot
Current Power State : D0 (Device operational, no power saving)

ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!

IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
Shared IRQs: There are no shared PCI IRQs



  #2  
Old December 2nd 04, 05:09 PM
JAD
external usenet poster
 
Posts: n/a
Default

change PnP Os installed? to the opposite of what you have now in the
bios...yes/no


"claude" wrote in message
...
I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
the following message:

"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"

Does anyone have an idea about it ?

Thanks for you help

Claude

PS: Please find the complete results of the tests (displayed in a DOS
window):

Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
1996-2004a.

PCI BIOS Version 2.10 found!
Number of PCI Busses : 1
PCI Characteristics : Config Mechanism 1

Searching for PCI Devices using the System BIOS

Vendor 8086h Intel Corporation
Device 7100h 82439TX 430TX System Controller
Command 0006h (Memory Access, BusMaster)
Status 2200h (Received Master Abort, Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Vendor 8086h Intel Corporation
Device 7110h 82371AB PIIX4 ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA

Vendor 8086h Intel Corporation
Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Address 4 is an I/O Port : 0000FFA0h

Vendor 8086h Intel Corporation
Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Address 4 is an I/O Port : 0000DB00h
System IRQ 3, INT# D

Vendor 8086h Intel Corporation
Device 7113h 82371AB PIIX4 Power Management Controller
Command 0003h (I/O Access, Memory Access)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other

Vendor 1002h ATI Technologies
Device 4755h Rage 3D II+ [Mach64 GTB]
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 9Ah, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
Subsystem Vendor 1002h ATI Technologies
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
Address 1 is an I/O Port : 0000DE00h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
Expansion ROM of 0Kb decoded by this card

Vendor 10ECh Realtek Semiconductor
Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
Command 0105h (I/O Access, BusMaster, System Errors)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
Medium Timing)
Revision 10h, Header Type 00h, Bus Latency 80h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
Subsystem Vendor 1799h Belkin Research and Development Labs
Address 0 is an I/O Port : 0000DC00h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
System IRQ 11, INT# A
Expansion ROM of 0Kb decoded by this card
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# from mode(s) D1, D2, D3hot
Current Power State : D0 (Device operational, no power saving)

ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!

IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
Shared IRQs: There are no shared PCI IRQs





  #3  
Old December 2nd 04, 05:11 PM
JAD
external usenet poster
 
Posts: n/a
Default

also is that a VIA based mainboard? miniport driver for irq steering may
not be loaded. ACPI
set to?


"claude" wrote in message
...
I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
the following message:

"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"

Does anyone have an idea about it ?

Thanks for you help

Claude

PS: Please find the complete results of the tests (displayed in a DOS
window):

Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
1996-2004a.

PCI BIOS Version 2.10 found!
Number of PCI Busses : 1
PCI Characteristics : Config Mechanism 1

Searching for PCI Devices using the System BIOS

Vendor 8086h Intel Corporation
Device 7100h 82439TX 430TX System Controller
Command 0006h (Memory Access, BusMaster)
Status 2200h (Received Master Abort, Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Vendor 8086h Intel Corporation
Device 7110h 82371AB PIIX4 ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA

Vendor 8086h Intel Corporation
Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Address 4 is an I/O Port : 0000FFA0h

Vendor 8086h Intel Corporation
Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Address 4 is an I/O Port : 0000DB00h
System IRQ 3, INT# D

Vendor 8086h Intel Corporation
Device 7113h 82371AB PIIX4 Power Management Controller
Command 0003h (I/O Access, Memory Access)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other

Vendor 1002h ATI Technologies
Device 4755h Rage 3D II+ [Mach64 GTB]
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 9Ah, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
Subsystem Vendor 1002h ATI Technologies
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
Address 1 is an I/O Port : 0000DE00h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
Expansion ROM of 0Kb decoded by this card

Vendor 10ECh Realtek Semiconductor
Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
Command 0105h (I/O Access, BusMaster, System Errors)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
Medium Timing)
Revision 10h, Header Type 00h, Bus Latency 80h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
Subsystem Vendor 1799h Belkin Research and Development Labs
Address 0 is an I/O Port : 0000DC00h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
System IRQ 11, INT# A
Expansion ROM of 0Kb decoded by this card
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# from mode(s) D1, D2, D3hot
Current Power State : D0 (Device operational, no power saving)

ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!

IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
Shared IRQs: There are no shared PCI IRQs





  #4  
Old December 2nd 04, 05:28 PM
claude
external usenet poster
 
Posts: n/a
Default

JAD a écrit:
also is that a VIA based mainboard?


What do you mean with VIA ?

miniport driver for irq steering may
not be loaded.


I forgot to say that my OS is W98SE.
In the PCI bus properties, I have everything crossed (in "use the IRQ
steering) except "Getting the IRQ table from PCIBIOS 2.1 in protected mode.

ACPI set to?


I don't think I have this option in the bios settings (but I'll check it )

thanks



"claude" wrote in message
...

I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
the following message:

"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"

Does anyone have an idea about it ?

Thanks for you help

Claude

PS: Please find the complete results of the tests (displayed in a DOS
window):

Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
1996-2004a.

PCI BIOS Version 2.10 found!
Number of PCI Busses : 1
PCI Characteristics : Config Mechanism 1

Searching for PCI Devices using the System BIOS

Vendor 8086h Intel Corporation
Device 7100h 82439TX 430TX System Controller
Command 0006h (Memory Access, BusMaster)
Status 2200h (Received Master Abort, Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Vendor 8086h Intel Corporation
Device 7110h 82371AB PIIX4 ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA

Vendor 8086h Intel Corporation
Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Address 4 is an I/O Port : 0000FFA0h

Vendor 8086h Intel Corporation
Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Address 4 is an I/O Port : 0000DB00h
System IRQ 3, INT# D

Vendor 8086h Intel Corporation
Device 7113h 82371AB PIIX4 Power Management Controller
Command 0003h (I/O Access, Memory Access)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other

Vendor 1002h ATI Technologies
Device 4755h Rage 3D II+ [Mach64 GTB]
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 9Ah, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
Subsystem Vendor 1002h ATI Technologies
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
Address 1 is an I/O Port : 0000DE00h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
Expansion ROM of 0Kb decoded by this card

Vendor 10ECh Realtek Semiconductor
Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
Command 0105h (I/O Access, BusMaster, System Errors)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
Medium Timing)
Revision 10h, Header Type 00h, Bus Latency 80h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
Subsystem Vendor 1799h Belkin Research and Development Labs
Address 0 is an I/O Port : 0000DC00h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
System IRQ 11, INT# A
Expansion ROM of 0Kb decoded by this card
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# from mode(s) D1, D2, D3hot
Current Power State : D0 (Device operational, no power saving)

ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!

IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
Shared IRQs: There are no shared PCI IRQs







  #5  
Old December 2nd 04, 05:30 PM
claude
external usenet poster
 
Posts: n/a
Default



JAD a écrit:
change PnP Os installed? to the opposite of what you have now in the
bios...yes/no


I tried both. but, I 'll check it again

thanks



"claude" wrote in message
...

I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
the following message:

"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"

Does anyone have an idea about it ?

Thanks for you help

Claude

PS: Please find the complete results of the tests (displayed in a DOS
window):

Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
1996-2004a.

PCI BIOS Version 2.10 found!
Number of PCI Busses : 1
PCI Characteristics : Config Mechanism 1

Searching for PCI Devices using the System BIOS

Vendor 8086h Intel Corporation
Device 7100h 82439TX 430TX System Controller
Command 0006h (Memory Access, BusMaster)
Status 2200h (Received Master Abort, Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Vendor 8086h Intel Corporation
Device 7110h 82371AB PIIX4 ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA

Vendor 8086h Intel Corporation
Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Address 4 is an I/O Port : 0000FFA0h

Vendor 8086h Intel Corporation
Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Address 4 is an I/O Port : 0000DB00h
System IRQ 3, INT# D

Vendor 8086h Intel Corporation
Device 7113h 82371AB PIIX4 Power Management Controller
Command 0003h (I/O Access, Memory Access)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other

Vendor 1002h ATI Technologies
Device 4755h Rage 3D II+ [Mach64 GTB]
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 9Ah, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
Subsystem Vendor 1002h ATI Technologies
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
Address 1 is an I/O Port : 0000DE00h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
Expansion ROM of 0Kb decoded by this card

Vendor 10ECh Realtek Semiconductor
Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
Command 0105h (I/O Access, BusMaster, System Errors)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
Medium Timing)
Revision 10h, Header Type 00h, Bus Latency 80h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
Subsystem Vendor 1799h Belkin Research and Development Labs
Address 0 is an I/O Port : 0000DC00h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
System IRQ 11, INT# A
Expansion ROM of 0Kb decoded by this card
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# from mode(s) D1, D2, D3hot
Current Power State : D0 (Device operational, no power saving)

ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!

IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
Shared IRQs: There are no shared PCI IRQs







  #6  
Old December 2nd 04, 05:38 PM
claude
external usenet poster
 
Posts: n/a
Default

Whatever the PnP OS settings (yes/no), I get the same result: No ROM PCI
IRQ routing table found.

I haven't found anything looking like an ACPI option in the bios settings.

claude a écrit:


JAD a écrit:

change PnP Os installed? to the opposite of what you have now in the
bios...yes/no



I tried both. but, I 'll check it again

thanks



"claude" wrote in message
...

I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
the following message:

"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"

Does anyone have an idea about it ?

Thanks for you help

Claude

PS: Please find the complete results of the tests (displayed in a DOS
window):

Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
1996-2004a.

PCI BIOS Version 2.10 found!
Number of PCI Busses : 1
PCI Characteristics : Config Mechanism 1

Searching for PCI Devices using the System BIOS

Vendor 8086h Intel Corporation
Device 7100h 82439TX 430TX System Controller
Command 0006h (Memory Access, BusMaster)
Status 2200h (Received Master Abort, Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Vendor 8086h Intel Corporation
Device 7110h 82371AB PIIX4 ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA

Vendor 8086h Intel Corporation
Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Address 4 is an I/O Port : 0000FFA0h

Vendor 8086h Intel Corporation
Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Address 4 is an I/O Port : 0000DB00h
System IRQ 3, INT# D

Vendor 8086h Intel Corporation
Device 7113h 82371AB PIIX4 Power Management Controller
Command 0003h (I/O Access, Memory Access)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other

Vendor 1002h ATI Technologies
Device 4755h Rage 3D II+ [Mach64 GTB]
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 9Ah, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
Subsystem Vendor 1002h ATI Technologies
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
Address 1 is an I/O Port : 0000DE00h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
Expansion ROM of 0Kb decoded by this card

Vendor 10ECh Realtek Semiconductor
Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
Command 0105h (I/O Access, BusMaster, System Errors)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
Medium Timing)
Revision 10h, Header Type 00h, Bus Latency 80h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
Subsystem Vendor 1799h Belkin Research and Development Labs
Address 0 is an I/O Port : 0000DC00h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
System IRQ 11, INT# A
Expansion ROM of 0Kb decoded by this card
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# from mode(s) D1, D2, D3hot
Current Power State : D0 (Device operational, no power saving)

ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!

IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
Shared IRQs: There are no shared PCI IRQs








  #7  
Old December 2nd 04, 06:03 PM
claude
external usenet poster
 
Posts: n/a
Default

I don't know if this can help you, but, I have a dual boot W98SE/linux.
and, in the linux logs, I have this curious message:
"Nov 26 16:24:27 kernel: PCI: Cannot allocate resource region 0 of
device 0000:00:08.0"

the device 8 is my vga card as described he

Bus 0, device 8, function 0:
VGA compatible controller: ATI Technologies Inc 3D Rage II+ 215GTB
[Mach64 GTB] (rev 154).
Master Capable. Latency=64. Min Gnt=8.
Non-prefetchable 32 bit memory at 0x10000000 [0x10ffffff].
I/O at 0xde00 [0xdeff].
Non-prefetchable 32 bit memory at 0xffeff000 [0xffefffff].

It would seem that my processor is not able to access directly to the
video RAM... but, i'm not sure of this.
what do you think of this issue ?

thanks


JAD a écrit:
also is that a VIA based mainboard? miniport driver for irq steering may
not be loaded. ACPI
set to?


"claude" wrote in message
...

I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
the following message:

"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"

Does anyone have an idea about it ?

Thanks for you help

Claude

PS: Please find the complete results of the tests (displayed in a DOS
window):

Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
1996-2004a.

PCI BIOS Version 2.10 found!
Number of PCI Busses : 1
PCI Characteristics : Config Mechanism 1

Searching for PCI Devices using the System BIOS

Vendor 8086h Intel Corporation
Device 7100h 82439TX 430TX System Controller
Command 0006h (Memory Access, BusMaster)
Status 2200h (Received Master Abort, Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Vendor 8086h Intel Corporation
Device 7110h 82371AB PIIX4 ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA

Vendor 8086h Intel Corporation
Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Address 4 is an I/O Port : 0000FFA0h

Vendor 8086h Intel Corporation
Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Address 4 is an I/O Port : 0000DB00h
System IRQ 3, INT# D

Vendor 8086h Intel Corporation
Device 7113h 82371AB PIIX4 Power Management Controller
Command 0003h (I/O Access, Memory Access)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other

Vendor 1002h ATI Technologies
Device 4755h Rage 3D II+ [Mach64 GTB]
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 9Ah, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
Subsystem Vendor 1002h ATI Technologies
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
Address 1 is an I/O Port : 0000DE00h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
Expansion ROM of 0Kb decoded by this card

Vendor 10ECh Realtek Semiconductor
Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
Command 0105h (I/O Access, BusMaster, System Errors)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
Medium Timing)
Revision 10h, Header Type 00h, Bus Latency 80h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
Subsystem Vendor 1799h Belkin Research and Development Labs
Address 0 is an I/O Port : 0000DC00h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
System IRQ 11, INT# A
Expansion ROM of 0Kb decoded by this card
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# from mode(s) D1, D2, D3hot
Current Power State : D0 (Device operational, no power saving)

ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!

IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
Shared IRQs: There are no shared PCI IRQs







  #8  
Old December 3rd 04, 03:54 AM
David Maynard
external usenet poster
 
Posts: n/a
Default

claude wrote:

I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get=20
the following message:
=20
"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"
=20
Does anyone have an idea about it ?


Your BIOS apparently doesn't have a PCI IRQ Routing Table so Windows will=
=20
not be able to dynamically route PCI IRQ assignments.

http://www.microsoft.com/whdc/archive/pciirq.mspx


Thanks for you help
=20
Claude
=20
PS: Please find the complete results of the tests (displayed in a DOS=20
window):
=20
Craig Hart's PCI+AGP bus sniffer, version 0.49=DF, freeware made in=20
1996-2004a.
=20
PCI BIOS Version 2.10 found!
Number of PCI Busses : 1
PCI Characteristics : Config Mechanism 1
=20
Searching for PCI Devices using the System BIOS
=20
Vendor 8086h Intel Corporation
Device 7100h 82439TX 430TX System Controller
Command 0006h (Memory Access, BusMaster)
Status 2200h (Received Master Abort, Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
=20
Vendor 8086h Intel Corporation
Device 7110h 82371AB PIIX4 ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
=20
Vendor 8086h Intel Corporation
Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Address 4 is an I/O Port : 0000FFA0h
=20
Vendor 8086h Intel Corporation
Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Address 4 is an I/O Port : 0000DB00h
System IRQ 3, INT# D
=20
Vendor 8086h Intel Corporation
Device 7113h 82371AB PIIX4 Power Management Controller
Command 0003h (I/O Access, Memory Access)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other
=20
Vendor 1002h ATI Technologies
Device 4755h Rage 3D II+ [Mach64 GTB]
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 9Ah, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
Subsystem Vendor 1002h ATI Technologies
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
Address 1 is an I/O Port : 0000DE00h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
Expansion ROM of 0Kb decoded by this card
=20
Vendor 10ECh Realtek Semiconductor
Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
Command 0105h (I/O Access, BusMaster, System Errors)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
Medium Timing)
Revision 10h, Header Type 00h, Bus Latency 80h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
Subsystem Vendor 1799h Belkin Research and Development Labs
Address 0 is an I/O Port : 0000DC00h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
System IRQ 11, INT# A
Expansion ROM of 0Kb decoded by this card
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# from mode(s) D1, D2, D3hot
Current Power State : D0 (Device operational, no power saving)
=20
ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!
=20
IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
Shared IRQs: There are no shared PCI IRQs
=20
=20
=20


  #9  
Old December 3rd 04, 09:45 AM
Claude
external usenet poster
 
Posts: n/a
Default


"David Maynard" a écrit dans le message de
...
claude wrote:

I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
the following message:

"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"

Does anyone have an idea about it ?


Your BIOS apparently doesn't have a PCI IRQ Routing Table so Windows will
not be able to dynamically route PCI IRQ assignments.

http://www.microsoft.com/whdc/archive/pciirq.mspx



what's the impact of this missing table ? should I do anything with the BIOS
?
in the following link (http://www.microsoft.com/whdc/archive/pciixa.mspx),
they talk about my chipset (PIIX4 chip set): it would be possible to get the
IRQ routing on my W98SE. I only need to run regedit and update the right
registry. but, I know there's some risk to use regedit....

thanks
Claude


  #10  
Old December 3rd 04, 09:59 AM
David Maynard
external usenet poster
 
Posts: n/a
Default

Claude wrote:

"David Maynard" a =E9crit dans le message de
...
claude wrote:
=20
=20
I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
the following message:

"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"

Does anyone have an idea about it ?

=20
=20
Your BIOS apparently doesn't have a PCI IRQ Routing Table so Windows wi=

ll
not be able to dynamically route PCI IRQ assignments.
=20
http://www.microsoft.com/whdc/archive/pciirq.mspx
=20
=20
=20
what's the impact of this missing table ?


Judging by the IRQ list you gave, pretty much nothing.

should I do anything with the BIOS


You could check for a BIOS update.

What motherboard is it anyway?

?
in the following link (http://www.microsoft.com/whdc/archive/pciixa.msp=

x),
they talk about my chipset (PIIX4 chip set): it would be possible to ge=

t the
IRQ routing on my W98SE. I only need to run regedit and update the righ=

t
registry. but, I know there's some risk to use regedit....


That page isn't really for users but it suggests that maybe you didn't lo=
ad=20
all the motherboard drivers: in particular the miniport driver, if it has=
one.

=20
thanks
Claude


Besides you having found this IRQ table message in a diagnostic program, =

just exactly what in your system isn't working?

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
corrupted partition table - help needed! Justin Case General 0 August 3rd 04 09:22 AM
my new mobo o/c's great rockerrock Overclocking AMD Processors 9 June 30th 04 08:17 PM
sdram modules found only 48mb but i insert 64mb crazyman General 1 September 19th 03 09:18 AM
sector not found reading drive c gbell Homebuilt PC's 2 September 7th 03 04:37 PM
What is a QVL memory table ljg Homebuilt PC's 3 August 13th 03 10:40 PM


All times are GMT +1. The time now is 11:43 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.