![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
I'm finding that my DVD drive is very stuttery and basically useless - I'm
wondering if its been set up properly. The CD-ROM drive is master, but the IDE cable goes into the DVD drive first (ie is closest to the motherboard IDE controller). If the CD drive is master, is it going to the cd drive to find the dvd drive to play the dvd first? Surely that's not efficient - but then again, the cable is closer to the motherboard from the DVD drive... So, I'm not clear on the way it works speed-wise. My graphics card incidentally, is a Geforce MX440 and I have 512 ram with a 1800+xp athlon, so my system should be able to play DVDs fine. Its the same with different software. Thanks for any clarification on the above problem. |
#2
|
|||
|
|||
![]()
"-" writes:
I'm finding that my DVD drive is very stuttery and basically useless - I'm wondering if its been set up properly. The CD-ROM drive is master, but the IDE cable goes into the DVD drive first (ie is closest to the motherboard IDE controller). If the CD drive is master, is it going to the cd drive to find the dvd drive to play the dvd first? Surely that's not efficient - but then again, the cable is closer to the motherboard from the DVD drive... So, I'm not clear on the way it works speed-wise. My graphics card incidentally, is a Geforce MX440 and I have 512 ram with a 1800+xp athlon, so my system should be able to play DVDs fine. Its the same with different software. The cable order shouldn't matter provided master and slave are set correctly. What may be happening is that your DVD drive is dumbing down to the IDE bus speed of your CD-ROM drive. I'd suggest setting the DVD drive as master, and temporarily pulling the CD-ROM drive off the IDE cable and see if the problem goes away. If the problem does go away, your solution is likely to either not use the CD-ROM drive anymore, replace it with one that supports the same IDE bus speed as your DVD drive, or purchase another IDE card to run the CD-ROM drive on an IDE interface that is separate from both your hard disks and the DVD drive. Best Regards, -- Todd H. http://www.toddh.net/ |
#3
|
|||
|
|||
![]()
On Mon, 24 Nov 2003 17:31:34 -0000, "-" wrote:
I'm finding that my DVD drive is very stuttery and basically useless - I'm wondering if its been set up properly. The CD-ROM drive is master, but the IDE cable goes into the DVD drive first (ie is closest to the motherboard IDE controller). If the CD drive is master, is it going to the cd drive to find the dvd drive to play the dvd first? Surely that's not efficient - but then again, the cable is closer to the motherboard from the DVD drive... So, I'm not clear on the way it works speed-wise. My graphics card incidentally, is a Geforce MX440 and I have 512 ram with a 1800+xp athlon, so my system should be able to play DVDs fine. Its the same with different software. Thanks for any clarification on the above problem. Windows? Check Device Manager, enable DMA mode (if available) ... not having DMA enabled is the most likely cause. Possibly you have a buggy drive, one or the other, and it would help to switch them, their master slave positions, but there is no issue involved with finding the DVD drive to play a DVD as you wrote, it would be fine where it is if everything else is working right. Indeed your system is much faster than needed to play a DVD, takes about a 400MHz system and vidcard with MPEG acceleration or 200MHz faster CPU to compensate for a video card shortcoming, which doesn't apply to your video card at all... may not be the greatest for modern games but a lot faster than needed for DVD. Dave |
#4
|
|||
|
|||
![]()
On Mon, 24 Nov 2003 17:31:34 -0000, Knowing that it was a Hollywood
invention that lemmings jump off cliffs "-" wrote : I'm finding that my DVD drive is very stuttery and basically useless - I'm wondering if its been set up properly. The CD-ROM drive is master, but the IDE cable goes into the DVD drive first (ie is closest to the motherboard IDE controller). If the CD drive is master, is it going to the cd drive to find the dvd drive to play the dvd first? Surely that's not efficient - but then again, the cable is closer to the motherboard from the DVD drive... So, I'm not clear on the way it works speed-wise. My graphics card incidentally, is a Geforce MX440 and I have 512 ram with a 1800+xp athlon, so my system should be able to play DVDs fine. Its the same with different software. Thanks for any clarification on the above problem. Try here, http://www.geocities.com/sheppola/hard.html http://www.geocities.com/sheppola/cdsetup.html and for win9X/ME, http://www.geocities.com/sheppola/mode.html and, http://www.geocities.com/sheppola/diag.html HTH ![]() -- Free Windows/PC help, http://www.geocities.com/sheppola/trouble.html email shepATpartyheld.de Free songs download, http://www.soundclick.com/bands/8/nomessiahsmusic.htm |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Multi-boot Windows XP without special software | Timothy Daniels | General | 11 | December 12th 03 05:38 AM |
primary slave drive fails (after bug with nero image drive) | Jean | General | 1 | October 8th 03 02:33 PM |
Help! WinXP can't tell that my 2nd hard drive is already formatted | FitPhillyGuy | General | 12 | September 26th 03 03:38 AM |
slave setting for hard drive | kony | General | 0 | August 6th 03 10:57 PM |
set CDROM as master not slave? | kony | General | 1 | June 28th 03 07:40 AM |