ddr1 memory

i got the third stick of ddr1 memory.
putting it in the system. i run a memtest.

u see the cl is 2.5 not 3 which is no the stick.
the bios is set to auto. should i change the bios to maual
and change it back, or will it run ok with that setting.
(run boinc on the system at 100%)

stick is kingston valueram.

john wrote:
i got the third stick of ddr1 memory.
putting it in the system. i run a memtest.

u see the cl is 2.5 not 3 which is no the stick.
the bios is set to auto. should i change the bios to maual
and change it back, or will it run ok with that setting.
(run boinc on the system at 100%)

stick is kingston valueram.


If the memory settings in the BIOS are "Auto",
and you add multiple sticks of memory, the BIOS
will do a good job of selecting settings to use.

If you set the BIOS to "Manual" and enter the
numbers yourself, then *you* are responsible
for selecting the right numbers to use.

To make an example

1) I have one stick of memory with CAS2.5
2) I have a second stick of memory with CAS3
3) My BIOS memory section is "Auto"

then the BIOS will set the memory controller to CAS3.
CAS3 is exactly what is needed for (2). CAS3 is
slower than the CAS2.5 in (1), so that stick is
happy also.

The settings selected apply to all memory sticks
at the same time. The computer doesn't feed
each stick different values. The sticks all
share the same hardware busses, so the
settings are shared values as well. The
BIOS tries to select settings slow enough,
so that the slowest of all the memory sticks
will be satisfied and run well.

HTH,
Paul

the setting are set as auto in the bios.

when i put the new stick in and i saw the setting were now lower. was
wondering if it would be a problem.


"Paul" wrote in message
...
john wrote:
i got the third stick of ddr1 memory.
putting it in the system. i run a memtest.

u see the cl is 2.5 not 3 which is no the stick.
the bios is set to auto. should i change the bios to maual
and change it back, or will it run ok with that setting.
(run boinc on the system at 100%)

stick is kingston valueram.


If the memory settings in the BIOS are "Auto",
and you add multiple sticks of memory, the BIOS
will do a good job of selecting settings to use.

If you set the BIOS to "Manual" and enter the
numbers yourself, then *you* are responsible
for selecting the right numbers to use.

To make an example

1) I have one stick of memory with CAS2.5
2) I have a second stick of memory with CAS3
3) My BIOS memory section is "Auto"

then the BIOS will set the memory controller to CAS3.
CAS3 is exactly what is needed for (2). CAS3 is
slower than the CAS2.5 in (1), so that stick is
happy also.

The settings selected apply to all memory sticks
at the same time. The computer doesn't feed
each stick different values. The sticks all
share the same hardware busses, so the
settings are shared values as well. The
BIOS tries to select settings slow enough,
so that the slowest of all the memory sticks
will be satisfied and run well.

HTH,
Paul

this is the setting that the bios has set at boot time.

2.5-3-3-7

from a memtest program.

john wrote:
this is the setting that the bios has set at boot time.

2.5-3-3-7

from a memtest program.



If you had a stick with a rating of 3-3-3-8, then
the BIOS would have made a mistake. If all the
sticks are CAS 2.5 or CAS 2.0, then that would be
a good setting.

You'd really need to give a full description of each
stick. You can get details from CPUZ. Run the .exe.
Go to "About" tab. Select "Register Dump txt" and
it will make a text file with the results for your
computer.

http://www.cpuid.com/cpuz.php

*******
This is a selective snip from my cpuz.txt register dump.
The "DIMM" part, is what the DIMM is "advertising" as options.
The SPD chip on the DIMM, holds this timing table, and
CPUZ can read it out.

DIMM #1

Timings table
Frequency (MHz) 200 266 333
CAS# 3.0 4.0 5.0
RAS# to CAS# delay 3 4 5
RAS# Precharge 3 4 5
TRAS 9 12 15
TRC 12 16 20

Copy over each DIMM table. My second DIMM is the same as the first.

DIMM #2

Timings table
Frequency (MHz) 200 266 333
CAS# 3.0 4.0 5.0
RAS# to CAS# delay 3 4 5
RAS# Precharge 3 4 5
TRAS 9 12 15
TRC 12 16 20

The section above that, called "Chipset", shows what my BIOS selected as
operating conditions

Chipset

Northbridge VIA PT880 Pro rev. 00
Southbridge VIA VT8237S rev. 00
Graphic Interface AGP
AGP Revision 3.0
AGP Transfer Rate 8x
AGP SBA supported, enabled
Memory Type DDR2
Memory Size 2048 MBytes
Channels Dual
Memory Frequency 266.0 MHz (3:4) ----- 266*2 means DDR2-533 in my case
DRAM Interleave 4-way
CAS# 3.0 \
RAS# to CAS# 3 \___ BIOS is using 3-3-3-12, because
RAS# Precharge 3 / I forced it to do that :-)
Cycle Time (tRAS) 12 /
Command Rate 1T
*******

If you want comments on your particular settings, then
provide some info from the CPUZ register dump.

Paul

this is the dump.

Chipset
------------------------------------------------------------------------------

Northbridge NVIDIA GeForce 6100 rev. A2
Southbridge NVIDIA nForce 410/430 MCP rev. A3
Memory Type DDR
Memory Size 2560 MBytes
Channels Single
Memory Frequency 157.9 MHz (CPU/14)
CAS# 2.5
RAS# to CAS# 3
RAS# Precharge 3
Cycle Time (tRAS) 7
Bank Cycle Time (tRC) 10
DRAM Idle Timer 16
Command Rate 2T


Memory SPD
------------------------------------------------------------------------------

DIMM #1

General
Memory type DDR
Manufacturer (ID) Kingston (7F98000000000000)
Size 1024 MBytes
Max bandwidth PC3200 (200 MHz)
Part number K
Serial number 732698DC
Manufacturing date Week 24/Year 07

Attributes
Number of banks 2
Data width 64 bits
Correction None
Registered no
Buffered no
Nominal Voltage 2.50 Volts
EPP no
XMP no

Timings table
Frequency (MHz) 166 200
CAS# 2.5 3.0
RAS# to CAS# delay 3 3
RAS# Precharge 3 3
TRAS 7 8


DIMM #2

General
Memory type DDR
Manufacturer (ID) Kingston (7F98000000000000)
Size 512 MBytes
Max bandwidth PC3200 (200 MHz)
Part number K
Serial number 600FC249
Manufacturing date Week 49/Year 05

Attributes
Number of banks 2
Data width 64 bits
Correction None
Registered no
Buffered no
Nominal Voltage 2.50 Volts
EPP no
XMP no

Timings table
Frequency (MHz) 133 166 200
CAS# 2.0 2.5 3.0
RAS# to CAS# delay 2 3 3
RAS# Precharge 2 3 3
TRAS 6 7 8


DIMM #3

General
Memory type DDR
Manufacturer (ID) Kingston (7F98000000000000)
Size 1024 MBytes
Max bandwidth PC3200 (200 MHz)
Part number K
Serial number 64316877
Manufacturing date Week 12/Year 06

Attributes
Number of banks 2
Data width 64 bits
Correction None
Registered no
Buffered no
Nominal Voltage 2.50 Volts
EPP no
XMP no

Timings table
Frequency (MHz) 133 166 200
CAS# 2.0 2.5 3.0
RAS# to CAS# delay 2 3 3
RAS# Precharge 2 3 3
TRAS 6 7 8