A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » General Hardware & Peripherals » General
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

cannot format NTFS to Fat32



 
 
Thread Tools Display Modes
  #1  
Old July 9th 07, 04:14 AM posted to alt.comp.hardware
sillyputty[_2_]
external usenet poster
 
Posts: 57
Default cannot format NTFS to Fat32

I'm building a win98 box and want to use an old 2GB HD that was on a
winXP system. The drive was formated NTFS and I can't get it to
reformat to Fat32. During Win98 setup it says the drive needs
formating, but neither the fdisk or format commands will work. Fdisk
says: "No fixed disks present" and format says: "format not supported
on drive C:"

  #2  
Old July 9th 07, 05:04 AM posted to alt.comp.hardware
Grinder
external usenet poster
 
Posts: 1,321
Default cannot format NTFS to Fat32

sillyputty wrote:
I'm building a win98 box and want to use an old 2GB HD that was on a
winXP system. The drive was formated NTFS and I can't get it to
reformat to Fat32. During Win98 setup it says the drive needs
formating, but neither the fdisk or format commands will work. Fdisk
says: "No fixed disks present" and format says: "format not supported
on drive C:"


Ok, the second message first. You're not going to be able to format a
disk that you've booted from. I'm not sure what you're doing, but
that's the message you'll get if you attempt that. Boot from a floppy
disk that has fdisk and format (bootdisk.com probably has what you need.)

As for the first message, I would recommend disconnecting all hard
drives, except the one in question, and booting from your floppy disk.
Run fdisk. Can you see the hard drive? If you can't check your cabling
and jumpers. Still can't see it? If it's still a non-starter, get
diagnostic tools from the hard drive's manufacturer--generally on a
bootable floppy.

If you can see it in fdisk, drop all the partitions. Create a new
partition that spans the entire drive. (2 GB is ok for win98, but I
wouldn't mess with anything less.) At that point, you should be able to
drop out of fdisk and format the drive.

Oh, when fdisk starts up, say "Y" to Enable Large Drive Support?

  #3  
Old July 9th 07, 05:49 AM posted to alt.comp.hardware
Plato
external usenet poster
 
Posts: 184
Default cannot format NTFS to Fat32

sillyputty wrote:

I'm building a win98 box and want to use an old 2GB HD that was on a
winXP system. The drive was formated NTFS and I can't get it to
reformat to Fat32. During Win98 setup it says the drive needs
formating, but neither the fdisk or format commands will work. Fdisk
says: "No fixed disks present" and format says: "format not supported
on drive C:"


remove the partitions first using:
http://www.bootdisk.com/plan10/delpart.zip

--
http://www.bootdisk.com/


  #4  
Old July 11th 07, 06:30 AM posted to alt.comp.hardware
[email protected]
external usenet poster
 
Posts: 368
Default cannot format NTFS to Fat32

On Jul 9, 4:14 am, sillyputty wrote:
I'm building a win98 box and want to use an old 2GB HD that was on a
winXP system. The drive was formated NTFS and I can't get it to
reformat to Fat32. During Win98 setup it says the drive needs
formating, but neither the fdisk or format commands will work. Fdisk
says: "No fixed disks present" and format says: "format not supported
on drive C:"


Regarding the fdisk error. Fdisk can have issues viewing and deleting
NTFS partitions. Though i've had successes when its been just one
partition. Where I think it doesn't work, I got a different error.
Anyhow, you've probably run into one of these issues.
Regarding the format error. I think Format gives that error, because
normally, if you create a partition in e.g. fdisk, then when it comes
to formatting it, you can still go to C: , try to type DIR, and it
gives an error like "invalid boot media". THat's how it should be. You
can do format c: or I suppose, format c: /q, and it'll work. Whereas I
think when the partition is NTFS, DOS can't see it at all. And I guess
the format command has problems.


There are other ways to delete partitions.
An easy way,
Is to boot up from a win xp cd and use that to delete partitions. I
know you're not installing win xp, but you can still use the win xp
setup to do that. Then just quit the setup once the partition is
deleted
otherwise, it's finding some other software to do it. maybe some
little freeware prog somebody mentioned. Or a linux boot disk Or
plugging the hard drive into another machine, not booting from that
hard drive, and deleting the partition from e.g. win xp disk
management. You could do that quicker with a usb-ide adaptor, then
you don't have to open the machine.

win xp cd seems ideal if you have one lying around. I don't think i've
used it for that myself, but one could, and I prob would if fdisk
wasn't doing it. Or even anyway.. If I was more into linux i'd just
use a linux boot disk.

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
NTFS - FAT32 Citizen Bob General 5 October 20th 06 06:51 PM
FAT32 & NTFS phil General 14 January 25th 05 05:08 AM
NTFS to FAT32? Anomaly Storage (alternative) 44 November 10th 04 08:17 PM
NTFS v FAT32 Dave General 6 January 9th 04 05:20 AM
maxtor Sata drive won't format into NTFS (fat32 works) Joord General Hardware 2 December 16th 03 02:59 PM


All times are GMT +1. The time now is 04:29 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Copyright 2004-2022 HardwareBanter.
The comments are property of their posters.