If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
GA-8IK1100 (rev 1.0) + 9500pro Sapphire reset to 640x480 after freezing and device failure!!!
Hello everyone,
once a day, or once every couple of days, I experience computer freezing and sreen reset to minimal default. It happens very randomly, especially while I'm connected to the Internet, with eMule (v0.30c) or ShareAza (v1.8.9.34) on. At some point, out of the blue, the mouse pointer doesn't move anymore, the keyboard is locked up as the computer is freezing. Then the screen is reset to default 640x480 16colors with error message: "Windows has detected and recovered from a device failure - Please restart". When I retsart, everything goes back to normal, and works fine... If I check "VPU recover" in Catalyst control tab to enable it, the same thing happens, the monitor is powered off, the screen stays at 1024x748, and I get the message "a device failure has been detected and partially recovered - software render has been enabled - restart to set video to hardware render"... Any idea where does the problem come from? Defective Sapphire Radeon video card? USB or IRQ conflict? Internet attacks/intrusions killing/bombing my computer? eMule and/or ShareAza bugs? Thanx in advance for your help! Mark. My computer is as follows: =================== MB = Gigabyte GA-8IK1100 (Intel i875P / ICH5 chipset) CPU = Intel Pentium IV 2.4C (FSB 800) DDR = A-Data 2*256Mo PC3200 (Winbond BH-5 chips) dual channel VID = ATI Radeon 9500pro 128Mo (Omega Catalyst 3.9 drivers) HD = Hitachi/IBM Deskstar 120Go 7200 8Mo PSU = Fortron 350W ATX FSP350-60PN SND = onboard Realtek ALC655 audio chip PCI = none installed OS = Windows XP Pro SP1 (up to date) NET = AOL 8.0 MDM = Thomson Speed Touch 330 ADSL (300.7.0.2 driver) AVR = Norton Internet Security 2003 Pro (up to date) Windows System Information: ===================== IRQ 0 - System clock - OK IRQ 1 - Standard keyboard 101/102 keys PS/2 - OK IRQ 6 - Standard floppy drive controller - OK IRQ 8 - System Clock CMOS/real time - OK IRQ 9 - ACPI compatible Microsoft - OK IRQ 10 - Intel(R) 82801EB SMBus Controller - 24D3 - OK IRQ 13 - Arithmetic coprocessor - OK IRQ 14 - IDE main - OK IRQ 15 - IDE secondary - OK |
#2
|
|||
|
|||
I checked Windows XP Error Logs and I found the following error message:
Event ID = 108 Source = ati2mtag Type = Error Description = The driver ati2dvag for the display device \Device\Video0 got stuck in an infinite loop. This usually indicates a problem with the device itself or with the device driver programming the hardware incorrectly. Please check with your hardware device vendor for any driver updates. Any advice, idea, where does that infinite loop com from? Video card? Video driver? DDR? Thanx in advance for your help... "markOpolis" a écrit dans le message de ... Hello everyone, once a day, or once every couple of days, I experience computer freezing and sreen reset to minimal default. It happens very randomly, especially while I'm connected to the Internet, with eMule (v0.30c) or ShareAza (v1.8.9.34) on. At some point, out of the blue, the mouse pointer doesn't move anymore, the keyboard is locked up as the computer is freezing. Then the screen is reset to default 640x480 16colors with error message: "Windows has detected and recovered from a device failure - Please restart". When I retsart, everything goes back to normal, and works fine... If I check "VPU recover" in Catalyst control tab to enable it, the same thing happens, the monitor is powered off, the screen stays at 1024x748, and I get the message "a device failure has been detected and partially recovered - software render has been enabled - restart to set video to hardware render"... Any idea where does the problem come from? Defective Sapphire Radeon video card? USB or IRQ conflict? Internet attacks/intrusions killing/bombing my computer? eMule and/or ShareAza bugs? Thanx in advance for your help! Mark. My computer is as follows: =================== MB = Gigabyte GA-8IK1100 (Intel i875P / ICH5 chipset) CPU = Intel Pentium IV 2.4C (FSB 800) DDR = A-Data 2*256Mo PC3200 (Winbond BH-5 chips) dual channel VID = ATI Radeon 9500pro 128Mo (Omega Catalyst 3.9 drivers) HD = Hitachi/IBM Deskstar 120Go 7200 8Mo PSU = Fortron 350W ATX FSP350-60PN SND = onboard Realtek ALC655 audio chip PCI = none installed OS = Windows XP Pro SP1 (up to date) NET = AOL 8.0 MDM = Thomson Speed Touch 330 ADSL (300.7.0.2 driver) AVR = Norton Internet Security 2003 Pro (up to date) Windows System Information: ===================== IRQ 0 - System clock - OK IRQ 1 - Standard keyboard 101/102 keys PS/2 - OK IRQ 6 - Standard floppy drive controller - OK IRQ 8 - System Clock CMOS/real time - OK IRQ 9 - ACPI compatible Microsoft - OK IRQ 10 - Intel(R) 82801EB SMBus Controller - 24D3 - OK IRQ 13 - Arithmetic coprocessor - OK IRQ 14 - IDE main - OK IRQ 15 - IDE secondary - OK |
#3
|
|||
|
|||
"markOpolis" wrote in message
... I checked Windows XP Error Logs and I found the following error message: Event ID = 108 Source = ati2mtag Type = Error Description = The driver ati2dvag for the display device \Device\Video0 got stuck in an infinite loop. This usually indicates a problem with the device itself or with the device driver programming the hardware incorrectly. Please check with your hardware device vendor for any driver updates. Any advice, idea, where does that infinite loop com from? Video card? Video driver? DDR? Thanx in advance for your help... Disable APIC mode in the BIOS if it is disabled suspect a ram stick here`s my story which explains it; Before infinite loop my setup was; Athlon XP 1700 o/c XP 2000 @ 133mhz fsb Crucial 256MB PC2100 MICRON 256MB PC2100 MSI Geforce 4 Ti4200 8X ABIT AT7 MAX KT333 In the ever increasing desire to o/c further I decided to sell both the PC2100 and buy a stick of 512MB PC2700 as I knew the system was not stable running at 166mhz fsb (XP 2400 oc) and thought it becuase of the RAM not being rated for 166fsb. When I got the PC2700 I immediately started running it at 166mhz FSB but it was still not stable I thought at the higher speeds my CPU wasn`t being cooled enough (my cooler wasnt rated for XP 2400) and bought a Thermaltake Heatsink/Fan to replace the cheap coolermaster I was running - I was pretty sure this would give me the stability at 166fsb 2ghz while I was waiting for it to arrive I decided to push up the fsb to see what the max fsb the PC2700 RAM would POST at - I got it up to 185fsb and it POSTED a couple of times then it could no more - mysterious I thought. So I gave up on the high fsb and went back to 133mhz fsb and XP 2000 but I started getting spontaneous reboots did some reading on google and ended up restoring my software build from backup the spontaneous reboots were gone no permanent damage or so I thought. The CPU Cooler arrived next day and I was still unable to get stability at 166fsb and now I started noticing the infinite loop error but as I`d not had stability at 166fsb before I figured it was just the same stability problem I`d always had only at 166fsb. However when I went back down to 133fsb and XP 2000 the infinite loop persisted I started to get worried maybe it was the CPU I went back down to default clock XP 1700 and still I had the infinite loop problem. Now my system was not stable at any CPU / FSB clock! Then I read about the infinite loop problem on here and other places and thought what if I`d damaged my PSU somehow during my attempts at high fsb overclock as I seemed to recall getting more problems since then - spontaneous reboots which I got rid off but then the infinite loop seemed to arrive back then. I replaced the Q-TEC 550W with a brand new Q-TEC 400W as I knew I`d originally had stability with the Q-TEC 550W in the system when it was new so I still had faith in the brand and figured I had damaged it somehow. Well the 400W made no difference and I still had the infinite loop. So then I went on a long journey of discovery involving days/weeks of testing with fresh builds and Prime 95 untill finally I swapped the memory with a stick of PC2100 in my other PC and the infinite loop was gone. Then it dawned on me that I had damaged the memory by running at 185mhz fsb not the PSU. I sent the PC2700 ram back for replacement and and am now running a stable XP 2000 system - its still unstable at 166fsb but I don`t have the infinite loop anymore. So for me it was faulty memory they`re are other types of memory problems which are also becuase of faulty memory that I`ll agree but the infinite loop it one of them IMO. These other memory problems are similar in that they are both intermittent thats what makes them so difficult to solve. See my post on google groups http://tinyurl.com/w3t0 Therefore I believe if you have infinite loop its becuase either your memory is faulty or misconfigured - my memory was faulty plain and simple the recommended configuration for avoiding infinite loop is CPU @ 133fsb Memory @ 133fsb and CPU @ 166fsb Memory @ 166fsb - I had the recommended configuration and I had infinite loop - untill I got rid of the memory that incidently wouldn`t even POST in my other board. *UPDATE* I mentioned in the above passage that I had no stability at 166fsb and that the stability problems were not to do with the infinite loop - well tonight I went back and tried 166fsb again and the error @ 166fsb is the infinite loop - however my system is totally stable at 133fsb with no inifinite loop. Way way back however I did have a stable XP 1700 @ XP 2400 at 166fsb on this system then I decided to re-install and thats when all my stability problems at 166fsb started. Now the interesting part - when I re-installed the system when it was stable 166fsb I did so to restore a backup image of XP this backup image was installed with the APIC mode enabled in the BIOS therefore I was unable to set it to disable because XP would not load so I left it enabled - if you see my post from nlel1975 of a few months back you can see the problems I had with BIOS settings - I reckon a lot of these problems were becuase I had APIC enabled. I have tonight taken the plunge and re-installed XP with APIC disabled while I have lost my 2 year old XP install my system is now stable again at 166fsb no infinite loop! So infinite loop is caused by; APIC mode enabled at 166fsb Bad/Faulty RAM at any fsb CPU / Memory out of fsb sync Check your system for stability with Prime 95 http://www.mersenne.org/freesoft.htm This applies to this this issue; Event ID 108 The driver nv4disp.dll for the display device \Device\Video0 got stuck in an infinite loop. This usually indicates a problem with the device itself or with the device driver programming the hardware incorrectly. Please check with your hardware device vendor for any driver updates. Keywords: Monitor into standby |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
BIOS password. Ridiculously easy to reset it on Asus motherboards !? | Bo Jacobsen | Asus Motherboards | 4 | August 19th 04 10:43 AM |
Need Help Understanding OC results for 'old' Celery not liking Win2K | pgtr | Overclocking | 35 | July 10th 04 12:26 AM |
9600SE vs 9500PRO | jim fallon | Asus Motherboards | 28 | June 8th 04 01:19 AM |
AN7 - Lock at Colour Screen - Hard to reset CMOS? | Wayne Youngman | Overclocking AMD Processors | 4 | March 24th 04 04:04 AM |
Case Reset Button Woes | rcm | General | 5 | July 25th 03 06:02 PM |