If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#12
|
|||
|
|||
Using a DELL 2600 PowerEdge as a Desktop PC
wrote:
On Friday, September 20, 2013 2:47:15 PM UTC-4, Paul wrote: wrote: On Thursday, September 19, 2013 11:51:57 PM UTC-4, Paul wrote: wrote: I'm stuck at go since I cannot burn a CD. That is a project you should work on first. You should have a stack of re-writable media, and a burner. As you can get yourself out of a lot of binds with burner in hand. Like the password reset disc. Re-writable media is more expensive, but you can use it more than once (quick erase, followed by burn). And for a basic burning software, you can use Imgburn. Just remember to turn off the audio prompt feature, as the first time it'll blow your eardrums out :-) http://en.wikipedia.org/wiki/Imgburn Paul I actually have two stacks of writable disks. My burners haven't/can't been used because of problems with my "present working" systems. The final acting s though it is ready to die, which is why I'm trying to get this server working fast. (I think NERO came with my DVD drives). Ok, that is a CD player over a floppy drive. I didn't know. I had never seen a low profile CD player before. I hadn't though about resetting the password on the server because I didn't think I could use the system for basic stuff like surfing the internet and playing MP3s/DVDs using Windows Server 2000. How is this for an IDE PCI card?: http://newyork.craigslist.org/brk/sys/4002182680.html Thanks. Darren Harris Staten Island, New York. Does your Craigslist thing work with ATAPI (optical drives) ? With RAID controllers, you want a JBOD mode of operation for running individual hard drives. In a few cases, products only support RAID, so there would be a two disk minimum. The product in question is quite old, and would be fun finding documentation for it. At one time, Maxtor did a promotion, where they included an IDE controller card, inside the box their disk drives came in. I got one of these. The Ultra133 ones, as far as I know, do ATAPI OK. These can either be sold as Promise Ultra133, or sport the word "Maxtor" on the front, if they were from the batch of Maxtor promotional cards. http://www.ebay.com/itm/Maxtor-Ultra...item1c339f4a51 Promise stopped making those cards probably five years ago, and yet Ebay is still offering "new" ones from China. Things that make you go "hmmm". Paul The seller never got back to me, but I found another: http://newyork.craigslist.org/brk/sys/4082191520.html That have 8 IDE connections, but I really only need one and perhaps I should look for a card that allows for SATA drives also. I'm assuming getting the cards from China on Ebay would be a crap-shoot: http://www.ebay.com/sch/i.html?_saca...S ATA&_sop=15 But there are other options: http://www.ebay.com/sch/i.html?_odkw...ATA&_sa cat=0 Thanks. Darren Harris Staten Island, New York. At the current time, there are a fair number of products using VIA 6421 chips. That's two SATA ports and one IDE port (one ribbon cable). The SATA ports are SATA I rate. http://www.via.com.tw/en/products/pe...rial-ata_raid/ http://www.via.com.tw/en/products/pe..._raid/vt6421a/ A typical VT6421A card, with two internal SATA connectors, and one IDE. $15. http://images10.newegg.com/NeweggIma...132-012-12.jpg ******* According to Larry http://al.howardknight.net/msgid.cgi...egroups.com%3E when you buy a card like that, you want the VT6421A chip, as it's more likely to work with a SATA II drive. There was VT6421 and VT6421A and the "A" version is supposed to be fixed for SATA. "AFAIK, only older SiS and VIA chipsets (VIA VT6420, VT8237, VT8237R, VT8237R+, VT8237A) can't handle SATA 3Gb/s drives. but VT8237S and VT6421A are OK" I have a VT8237S here, and can vouch for it being "fixed". I don't own any VT6421A cards. The IDE connector will work in any case. What happens if the chip isn't a "fixed" one, is the SATA disk is not detected, due to speed negotiation failing to work. (VIA chip doesn't convince the interface to run at SATA I rates.) I've never seen any scope traces, to see what the parties on either end of the SATA cable, are trying to do in such a situation. ******* With regard to the Escalade, where are you going to find help and support for this ? Even if it supports JBOD and single disks, it might not work with an optical drive (ATAPI). http://newyork.craigslist.org/brk/sys/4082191520.html Paul |
#13
|
|||
|
|||
Using a DELL 2600 PowerEdge as a Desktop PC
On Saturday, September 21, 2013 5:03:48 PM UTC-4, Paul wrote:
wrote: On Friday, September 20, 2013 2:47:15 PM UTC-4, Paul wrote: wrote: On Thursday, September 19, 2013 11:51:57 PM UTC-4, Paul wrote: wrote: I'm stuck at go since I cannot burn a CD. That is a project you should work on first. You should have a stack of re-writable media, and a burner. As you can get yourself out of a lot of binds with burner in hand. Like the password reset disc. Re-writable media is more expensive, but you can use it more than once (quick erase, followed by burn). And for a basic burning software, you can use Imgburn. Just remember to turn off the audio prompt feature, as the first time it'll blow your eardrums out :-) http://en.wikipedia.org/wiki/Imgburn Paul I actually have two stacks of writable disks. My burners haven't/can't been used because of problems with my "present working" systems. The final acting s though it is ready to die, which is why I'm trying to get this server working fast. (I think NERO came with my DVD drives). Ok, that is a CD player over a floppy drive. I didn't know. I had never seen a low profile CD player before. I hadn't though about resetting the password on the server because I didn't think I could use the system for basic stuff like surfing the internet and playing MP3s/DVDs using Windows Server 2000. How is this for an IDE PCI card?: http://newyork.craigslist.org/brk/sys/4002182680.html Thanks. Darren Harris Staten Island, New York. Does your Craigslist thing work with ATAPI (optical drives) ? With RAID controllers, you want a JBOD mode of operation for running individual hard drives. In a few cases, products only support RAID, so there would be a two disk minimum. The product in question is quite old, and would be fun finding documentation for it. At one time, Maxtor did a promotion, where they included an IDE controller card, inside the box their disk drives came in. I got one of these. The Ultra133 ones, as far as I know, do ATAPI OK. These can either be sold as Promise Ultra133, or sport the word "Maxtor" on the front, if they were from the batch of Maxtor promotional cards. http://www.ebay.com/itm/Maxtor-Ultra...item1c339f4a51 Promise stopped making those cards probably five years ago, and yet Ebay is still offering "new" ones from China. Things that make you go "hmmm". Paul The seller never got back to me, but I found another: http://newyork.craigslist.org/brk/sys/4082191520.html That have 8 IDE connections, but I really only need one and perhaps I should look for a card that allows for SATA drives also. I'm assuming getting the cards from China on Ebay would be a crap-shoot: http://www.ebay.com/sch/i.html?_saca...S ATA&_sop=15 But there are other options: http://www.ebay.com/sch/i.html?_odkw...ATA&_sa cat=0 Thanks. Darren Harris Staten Island, New York. At the current time, there are a fair number of products using VIA 6421 chips. That's two SATA ports and one IDE port (one ribbon cable). The SATA ports are SATA I rate. http://www.via.com.tw/en/products/pe...rial-ata_raid/ http://www.via.com.tw/en/products/pe..._raid/vt6421a/ A typical VT6421A card, with two internal SATA connectors, and one IDE. $15. http://images10.newegg.com/NeweggIma...132-012-12.jpg ******* According to Larry http://al.howardknight.net/msgid.cgi...egroups.com%3E when you buy a card like that, you want the VT6421A chip, as it's more likely to work with a SATA II drive. There was VT6421 and VT6421A and the "A" version is supposed to be fixed for SATA. "AFAIK, only older SiS and VIA chipsets (VIA VT6420, VT8237, VT8237R, VT8237R+, VT8237A) can't handle SATA 3Gb/s drives. but VT8237S and VT6421A are OK" I have a VT8237S here, and can vouch for it being "fixed". I don't own any VT6421A cards. The IDE connector will work in any case. What happens if the chip isn't a "fixed" one, is the SATA disk is not detected, due to speed negotiation failing to work. (VIA chip doesn't convince the interface to run at SATA I rates.) I've never seen any scope traces, to see what the parties on either end of the SATA cable, are trying to do in such a situation. ******* With regard to the Escalade, where are you going to find help and support for this ? Even if it supports JBOD and single disks, it might not work with an optical drive (ATAPI). http://newyork.craigslist.org/brk/sys/4082191520.html Paul Ok, these have the VT6421A chip, so one of them should work: www.ebay.com/itm/161064813022 www.ebay.com/itm/170332514420 www.ebay.com/itm/350555428799 Thanks. Darren Harris Staten Island, New York. |
#14
|
|||
|
|||
Using a DELL 2600 PowerEdge as a Desktop PC
wrote:
Ok, these have the VT6421A chip, so one of them should work: www.ebay.com/itm/161064813022 www.ebay.com/itm/170332514420 www.ebay.com/itm/350555428799 Thanks. Darren Harris Staten Island, New York. Yes, these look like a good candidate for a cheap IDE. The keying on the card is 5V I think, so the card should fit in your single 33MHz, 32 bit PCI slot. (Second down, on the left) http://en.wikipedia.org/wiki/File:PCI_Keying.png Paul |
#15
|
|||
|
|||
Using a DELL 2600 PowerEdge as a Desktop PC
On Sunday, September 22, 2013 9:29:26 PM UTC-4, Paul wrote:
Yes, these look like a good candidate for a cheap IDE. The keying on the card is 5V I think, so the card should fit in your single 33MHz, 32 bit PCI slot. (Second down, on the left) http://en.wikipedia.org/wiki/File:PCI_Keying.png Paul First, I have the face plate off of the cabinet and there is no way to turn the machine on or off outside of plugging/unplugging the AC cord. (The orange light that was blinking on the front is gone). :-) BTW. F2 = Setup, F10 = Utility Mode, and F12 = PXE Boot. Anyway, after looking in the manual I found the information concerning the jumpers for the password is confusing, so I just took both of the jumpers off. (I think that was what I'm suppoed to do). It seems to have no effect, because I still can only get as far as the screen where I have to enter the password. I then attempted to take the battery out, but I must have pulled too hard because one side of the battery holder detached from the motherboard. http://s290.photobucket.com/user/Sta...ml?sort=3&o=69 My next boot attempt gave me a screen that said "No Boot Device". http://s290.photobucket.com/user/Sta...ml?sort=3&o=68 So I re-booted while pushing down on the battery only to get a screen that said "Invalid Configuration". http://s290.photobucket.com/user/Sta...?sort=3&o =71 BTW. If I can correct these problems I notice that there is an option in Setup that says "OS Install Mode". Would I need to turn that on to install a new OS? http://s290.photobucket.com/user/Sta...ml?sort=3&o=70 Thanks. Darren Harris Staten Island, New York. |
#16
|
|||
|
|||
Using a DELL 2600 PowerEdge as a Desktop PC
wrote:
On Sunday, September 22, 2013 9:29:26 PM UTC-4, Paul wrote: Yes, these look like a good candidate for a cheap IDE. The keying on the card is 5V I think, so the card should fit in your single 33MHz, 32 bit PCI slot. (Second down, on the left) http://en.wikipedia.org/wiki/File:PCI_Keying.png Paul First, I have the face plate off of the cabinet and there is no way to turn the machine on or off outside of plugging/unplugging the AC cord. (The orange light that was blinking on the front is gone). :-) As a general rule (haven't seen an exception yet), the power signal and the reset signal on the front, are momentary contact active low. The power pair, consists of POWER- and GND, and touching the two together for a moment, triggers power on. I do that on systems here, with the tip of a slot head screwdriver. As long as you can identify bits of exposed metal or pins corresponding to those two, you can turn it on. The RESET- and GND are similar. Touch the two together for just a moment, and the machine will be reset. In an emergency, you can even swap the POWER and RESET cable pairs, and use the RESET button as a POWER button. (As RESET isn't used quite as much, and you could live without a RESET button, using the RESET button to take the place of a broken POWER button. So you weren't as "disabled" as first appeared. Just a matter of finding out where the cable goes, and touching the two pins. To turn the power off, can require making contact between POWER- and GND for a period of four seconds or longer. When turning off the power, a timer is used, and so the momentary contact in that case must be maintained for a four second interval. BTW. F2 = Setup, F10 = Utility Mode, and F12 = PXE Boot. Anyway, after looking in the manual I found the information concerning the jumpers for the password is confusing, so I just took both of the jumpers off. (I think that was what I'm suppoed to do). To reset the password, you remove the jumper on PASSWD. To clear the NVRAM (CMOS), you insert its jumper. You only use the jumper long enough to clear the settings, then the jumper will be coming off again. The manual says to remove system power while fooling around with those. I suspect the NVRAM one is the most dangerous, in terms of damaging the ORing diode for 3VSB. But in any case, follow the instructions in the manual, when it says to remove system power (unplug). It seems to have no effect, because I still can only get as far as the screen where I have to enter the password. Make sure you are following the procedure in the manual. "The existing passwords are not disabled (erased) until the system boots with the password jumper plug removed. However, before you assign a new system and/or setup password, you must install the jumper plug." The system has to see the PASSWD jumper plug removed, to disable the password for that cycle. It could be a write enable signal for an EEPROM, rather than a traditional resetting jumper for all I know. I then attempted to take the battery out, but I must have pulled too hard because one side of the battery holder detached from the motherboard. http://s290.photobucket.com/user/Sta...ml?sort=3&o=69 You villain :-) Those are always tricky. And in this case, I would have advised against attacking it. Unless the thing is flat, leave it alone :-) My next boot attempt gave me a screen that said "No Boot Device". http://s290.photobucket.com/user/Sta...ml?sort=3&o=68 That means you've managed to "NVRAM" clear. Losing the battery caused the settings to be lost. If you wrote down all the settings, you can power up the system, enter the BIOS, and load all the necessary settings by hand. They will stay there, until the next power failure. Then you have to enter them again. As I have several systems here with flat batteries, I'm quite used to running systems that way (load settings, then use the computer). So I re-booted while pushing down on the battery only to get a screen that said "Invalid Configuration". http://s290.photobucket.com/user/Sta...?sort=3&o =71 It says to press F2 to enter the BIOS. Good luck getting the correct settings in there. You should really have taken digital camera photos of each setup screen page, for future reference. Now, you're screwed :-) Part of the fun is things like the SCSI setup. BTW. If I can correct these problems I notice that there is an option in Setup that says "OS Install Mode". Would I need to turn that on to install a new OS? http://s290.photobucket.com/user/Sta...ml?sort=3&o=70 OS Install Mode restricts the amount of RAM the system gets to use. It would be for situations where an OS cannot understand large amounts of memory. For example, if installing Windows 98, you might engage that. For most other purpose, leave it off so all memory is always detected. "OS Install Mode — Determines the maximum amount of memory available to the operating system. On sets the maximum memory available to the operating system to 256 MB. Off (default) makes all of the system memory available to the operating system. Some operating systems will not install with more than 2 GB of system memory. Turn this option On during operating system installation and Off after installation." The CMOS battery issue isn't the end of the world. What concerns me now, is will you ever figure out how all those BIOS settings should be configured ? It's a server, and should be a real challenge. HTH, Paul |
#17
|
|||
|
|||
Using a DELL 2600 PowerEdge as a Desktop PC
On Sunday, September 29, 2013 10:56:40 PM UTC-4, Paul wrote:
As a general rule (haven't seen an exception yet), the power signal and the reset signal on the front, are momentary contact active low. The power pair, consists of POWER- and GND, and touching the two together for a moment, triggers power on. I do that on systems here, with the tip of a slot head screwdriver. As long as you can identify bits of exposed metal or pins corresponding to those two, you can turn it on. There is only a power on/off switch. No reset button. The RESET- and GND are similar. Touch the two together for just a moment, and the machine will be reset. In an emergency, you can even swap the POWER and RESET cable pairs, and use the RESET button as a POWER button. (As RESET isn't used quite as much, and you could live without a RESET button, using the RESET button to take the place of a broken POWER button. So you weren't as "disabled" as first appeared. Just a matter of finding out where the cable goes, and touching the two pins. To turn the power off, can require making contact between POWER- and GND for a period of four seconds or longer. When turning off the power, a timer is used, and so the momentary contact in that case must be maintained for a four second interval. BTW. F2 = Setup, F10 = Utility Mode, and F12 = PXE Boot. Anyway, after looking in the manual I found the information concerning the jumpers for the password is confusing, so I just took both of the jumpers off. (I think that was what I'm suppoed to do). To reset the password, you remove the jumper on PASSWD. To clear the NVRAM (CMOS), you insert its jumper. You only use the jumper long enough to clear the settings, then the jumper will be coming off again. The manual says to remove system power while fooling around with those. I suspect the NVRAM one is the most dangerous, in terms of damaging the ORing diode for 3VSB. But in any case, follow the instructions in the manual, when it says to remove system power (unplug). It seems to have no effect, because I still can only get as far as the screen where I have to enter the password. Make sure you are following the procedure in the manual. "The existing passwords are not disabled (erased) until the system boots with the password jumper plug removed. However, before you assign a new system and/or setup password, you must install the jumper plug." The system has to see the PASSWD jumper plug removed, to disable the password for that cycle. It could be a write enable signal for an EEPROM, rather than a traditional resetting jumper for all I know. The password and CMOS consist of two 3-pin connectors on the motherboard. I had taken each 2-pin jumper off of both. Since this did not clear the password (or CMOS for that matter? I assumed that replacing the jumpers in the lower position might work. (But I never got to that because of what happened when I attempted to remove the battery). I then attempted to take the battery out, but I must have pulled too hard because one side of the battery holder detached from the motherboard. http://s290.photobucket.com/user/Sta...ml?sort=3&o=69 You villain :-) Those are always tricky. And in this case, I would have advised against attacking it. Unless the thing is flat, leave it alone :-) Well, I didn't know that. In the past I've temporarily removed or changed the battery on many other motherboards without issue. My next boot attempt gave me a screen that said "No Boot Device". http://s290.photobucket.com/user/Sta...ml?sort=3&o=68 That means you've managed to "NVRAM" clear. Losing the battery caused the settings to be lost. If you wrote down all the settings, you can power up the system, enter the BIOS, and load all the necessary settings by hand. They will stay there, until the next power failure. Then you have to enter them again. As I have several systems here with flat batteries, I'm quite used to running systems that way (load settings, then use the computer). So I re-booted while pushing down on the battery only to get a screen that said "Invalid Configuration". http://s290.photobucket.com/user/Sta...?sort=3&o =71 It says to press F2 to enter the BIOS. Good luck getting the correct settings in there. You should really have taken digital camera photos of each setup screen page, for future reference. Now, you're screwed :-) Part of the fun is things like the SCSI setup. What settings in the CMOS have to be correct in order to get back to the password screen? (Which I assume is still uncleared). Am I supposed to research information on the motherboard, hard drives, CD/Floppy/Tape drive, ram, and Adaptec SCSI card for information on what settings are needed? Or is it a matter of trial and error, rolling the dice with different settings? There is a single screen in BIOS that you have to scroll down a little to see everything. I would have included a picture of the BIOS screen, but today as feared the imminent failure of the pc I was using occurred and as a result I have to way to tranfer the image from my camera to a computer. (I was trying to get the DELL 2600 up and running so I could avoid all my data loss). Thanks. Darren Harris Staten Island, New York. |
#18
|
|||
|
|||
Using a DELL 2600 PowerEdge as a Desktop PC
wrote:
On Sunday, September 29, 2013 10:56:40 PM UTC-4, Paul wrote: As a general rule (haven't seen an exception yet), the power signal and the reset signal on the front, are momentary contact active low. The power pair, consists of POWER- and GND, and touching the two together for a moment, triggers power on. I do that on systems here, with the tip of a slot head screwdriver. As long as you can identify bits of exposed metal or pins corresponding to those two, you can turn it on. There is only a power on/off switch. No reset button. The RESET- and GND are similar. Touch the two together for just a moment, and the machine will be reset. In an emergency, you can even swap the POWER and RESET cable pairs, and use the RESET button as a POWER button. (As RESET isn't used quite as much, and you could live without a RESET button, using the RESET button to take the place of a broken POWER button. So you weren't as "disabled" as first appeared. Just a matter of finding out where the cable goes, and touching the two pins. To turn the power off, can require making contact between POWER- and GND for a period of four seconds or longer. When turning off the power, a timer is used, and so the momentary contact in that case must be maintained for a four second interval. BTW. F2 = Setup, F10 = Utility Mode, and F12 = PXE Boot. Anyway, after looking in the manual I found the information concerning the jumpers for the password is confusing, so I just took both of the jumpers off. (I think that was what I'm suppoed to do). To reset the password, you remove the jumper on PASSWD. To clear the NVRAM (CMOS), you insert its jumper. You only use the jumper long enough to clear the settings, then the jumper will be coming off again. The manual says to remove system power while fooling around with those. I suspect the NVRAM one is the most dangerous, in terms of damaging the ORing diode for 3VSB. But in any case, follow the instructions in the manual, when it says to remove system power (unplug). It seems to have no effect, because I still can only get as far as the screen where I have to enter the password. Make sure you are following the procedure in the manual. "The existing passwords are not disabled (erased) until the system boots with the password jumper plug removed. However, before you assign a new system and/or setup password, you must install the jumper plug." The system has to see the PASSWD jumper plug removed, to disable the password for that cycle. It could be a write enable signal for an EEPROM, rather than a traditional resetting jumper for all I know. The password and CMOS consist of two 3-pin connectors on the motherboard. I had taken each 2-pin jumper off of both. Since this did not clear the password (or CMOS for that matter? I assumed that replacing the jumpers in the lower position might work. (But I never got to that because of what happened when I attempted to remove the battery). I then attempted to take the battery out, but I must have pulled too hard because one side of the battery holder detached from the motherboard. http://s290.photobucket.com/user/Sta...ml?sort=3&o=69 You villain :-) Those are always tricky. And in this case, I would have advised against attacking it. Unless the thing is flat, leave it alone :-) Well, I didn't know that. In the past I've temporarily removed or changed the battery on many other motherboards without issue. My next boot attempt gave me a screen that said "No Boot Device". http://s290.photobucket.com/user/Sta...ml?sort=3&o=68 That means you've managed to "NVRAM" clear. Losing the battery caused the settings to be lost. If you wrote down all the settings, you can power up the system, enter the BIOS, and load all the necessary settings by hand. They will stay there, until the next power failure. Then you have to enter them again. As I have several systems here with flat batteries, I'm quite used to running systems that way (load settings, then use the computer). So I re-booted while pushing down on the battery only to get a screen that said "Invalid Configuration". http://s290.photobucket.com/user/Sta...?sort=3&o =71 It says to press F2 to enter the BIOS. Good luck getting the correct settings in there. You should really have taken digital camera photos of each setup screen page, for future reference. Now, you're screwed :-) Part of the fun is things like the SCSI setup. What settings in the CMOS have to be correct in order to get back to the password screen? (Which I assume is still uncleared). Am I supposed to research information on the motherboard, hard drives, CD/Floppy/Tape drive, ram, and Adaptec SCSI card for information on what settings are needed? Or is it a matter of trial and error, rolling the dice with different settings? There is a single screen in BIOS that you have to scroll down a little to see everything. I would have included a picture of the BIOS screen, but today as feared the imminent failure of the pc I was using occurred and as a result I have to way to tranfer the image from my camera to a computer. (I was trying to get the DELL 2600 up and running so I could avoid all my data loss). Thanks. Darren Harris Staten Island, New York. Whereas normal BIOS have a menu along the top, this menu is based on hitting enter on the appropriate line in the main screen (depicted here). This person is setting the hard drive boot order, using the Hard Disk Drive Sequence entry. This is a picture, when the SCSI card is removed and a TX2300 is in place. http://www.modlog.net/wp-content/upl...3/DSCF1021.jpg And this would be with the original hardware. http://www.modlog.net/wp-content/upl...3/DSCF1016.jpg As long as you know how to set everything in that screen (and at the levels below the main screen), you should be OK without a battery. If the power goes off, you just end up entering the settings again. The SCSI card has an INT 0x13 BIOS ROM on board, and when that code is loaded, it prints stuff on the screen. Sometimes, there is a separate utility, for setting up which drive to boot from or doing other configuration things. I seem to remember my old Adaptec card having something like that. SCSI cards usually are more fully featured, than run of the mill SATA or IDE cards. http://www.modlog.net/wp-content/upl...3/DSCF1012.jpg Paul |
#19
|
|||
|
|||
Using a DELL 2600 PowerEdge as a Desktop PC
On Monday, September 30, 2013 5:29:25 PM UTC-4, Paul wrote:
wrote: On Sunday, September 29, 2013 10:56:40 PM UTC-4, Paul wrote: As a general rule (haven't seen an exception yet), the power signal and the reset signal on the front, are momentary contact active low. The power pair, consists of POWER- and GND, and touching the two together for a moment, triggers power on. I do that on systems here, with the tip of a slot head screwdriver. As long as you can identify bits of exposed metal or pins corresponding to those two, you can turn it on. There is only a power on/off switch. No reset button. The RESET- and GND are similar. Touch the two together for just a moment, and the machine will be reset. In an emergency, you can even swap the POWER and RESET cable pairs, and use the RESET button as a POWER button. (As RESET isn't used quite as much, and you could live without a RESET button, using the RESET button to take the place of a broken POWER button. So you weren't as "disabled" as first appeared. Just a matter of finding out where the cable goes, and touching the two pins. To turn the power off, can require making contact between POWER- and GND for a period of four seconds or longer. When turning off the power, a timer is used, and so the momentary contact in that case must be maintained for a four second interval. BTW. F2 = Setup, F10 = Utility Mode, and F12 = PXE Boot. Anyway, after looking in the manual I found the information concerning the jumpers for the password is confusing, so I just took both of the jumpers off. (I think that was what I'm suppoed to do). To reset the password, you remove the jumper on PASSWD. To clear the NVRAM (CMOS), you insert its jumper. You only use the jumper long enough to clear the settings, then the jumper will be coming off again. The manual says to remove system power while fooling around with those. I suspect the NVRAM one is the most dangerous, in terms of damaging the ORing diode for 3VSB. But in any case, follow the instructions in the manual, when it says to remove system power (unplug). It seems to have no effect, because I still can only get as far as the screen where I have to enter the password. Make sure you are following the procedure in the manual. "The existing passwords are not disabled (erased) until the system boots with the password jumper plug removed. However, before you assign a new system and/or setup password, you must install the jumper plug." The system has to see the PASSWD jumper plug removed, to disable the password for that cycle. It could be a write enable signal for an EEPROM, rather than a traditional resetting jumper for all I know. The password and CMOS consist of two 3-pin connectors on the motherboard. I had taken each 2-pin jumper off of both. Since this did not clear the password (or CMOS for that matter? I assumed that replacing the jumpers in the lower position might work. (But I never got to that because of what happened when I attempted to remove the battery). I then attempted to take the battery out, but I must have pulled too hard because one side of the battery holder detached from the motherboard. http://s290.photobucket.com/user/Sta...ml?sort=3&o=69 You villain :-) Those are always tricky. And in this case, I would have advised against attacking it. Unless the thing is flat, leave it alone :-) Well, I didn't know that. In the past I've temporarily removed or changed the battery on many other motherboards without issue. My next boot attempt gave me a screen that said "No Boot Device". http://s290.photobucket.com/user/Sta...ml?sort=3&o=68 That means you've managed to "NVRAM" clear. Losing the battery caused the settings to be lost. If you wrote down all the settings, you can power up the system, enter the BIOS, and load all the necessary settings by hand. They will stay there, until the next power failure. Then you have to enter them again. As I have several systems here with flat batteries, I'm quite used to running systems that way (load settings, then use the computer). So I re-booted while pushing down on the battery only to get a screen that said "Invalid Configuration". http://s290.photobucket.com/user/Sta...?sort=3&o =71 It says to press F2 to enter the BIOS. Good luck getting the correct settings in there. You should really have taken digital camera photos of each setup screen page, for future reference. Now, you're screwed :-) Part of the fun is things like the SCSI setup. What settings in the CMOS have to be correct in order to get back to the password screen? (Which I assume is still uncleared). Am I supposed to research information on the motherboard, hard drives, CD/Floppy/Tape drive, ram, and Adaptec SCSI card for information on what settings are needed? Or is it a matter of trial and error, rolling the dice with different settings? There is a single screen in BIOS that you have to scroll down a little to see everything. I would have included a picture of the BIOS screen, but today as feared the imminent failure of the pc I was using occurred and as a result I have to way to tranfer the image from my camera to a computer. (I was trying to get the DELL 2600 up and running so I could avoid all my data loss). Thanks. Darren Harris Staten Island, New York. Whereas normal BIOS have a menu along the top, this menu is based on hitting enter on the appropriate line in the main screen (depicted here). This person is setting the hard drive boot order, using the Hard Disk Drive Sequence entry. This is a picture, when the SCSI card is removed and a TX2300 is in place. http://www.modlog.net/wp-content/upl...3/DSCF1021.jpg And this would be with the original hardware. http://www.modlog.net/wp-content/upl...3/DSCF1016.jpg As long as you know how to set everything in that screen (and at the levels below the main screen), you should be OK without a battery. If the power goes off, you just end up entering the settings again. The SCSI card has an INT 0x13 BIOS ROM on board, and when that code is loaded, it prints stuff on the screen. Sometimes, there is a separate utility, for setting up which drive to boot from or doing other configuration things. I seem to remember my old Adaptec card having something like that. SCSI cards usually are more fully featured, than run of the mill SATA or IDE cards. http://www.modlog.net/wp-content/upl...3/DSCF1012.jpg Paul OK. My present system didn't go down yet. My monitor plug has somehow fallen out. The following pics are the BIOS screen. The top and the with it scrolled down: http://i290.photobucket.com/albums/l...psec8039bf.jpg http://i290.photobucket.com/albums/l...psd1e87a9a.jpg I'll play around on it tonight to see if I can get it working again. Thanks. Darren Harris Staten Island, New York. |
#20
|
|||
|
|||
Using a DELL 2600 PowerEdge as a Desktop PC
Ok. I booted the DELL 2600 server about 60 times in an attempt to get back to the password screen (or past it).
I went into BIOS and under "Integrated Devices" changed "Embedded RAID Controller" from "Off" to "SCSI". (The RAID option causes a warning that data will be lost). http://i290.photobucket.com/albums/l...psc498632d.jpg This allows me to boot as far as the Windows 2000 Server splash screen: http://i290.photobucket.com/albums/l...ps5bd0f4cc.jpg, Followed by a "Inaccessible Boot Device" blue screen which I can't get past: http://i290.photobucket.com/albums/l...ps9b47479a.jpg (The blue screen tells me to run CHKDSK /F, but I don't know how to do that). A weird thing is that three times out of all the times I booted I got a slightly different BIOS screen that gave me an extra option. ?!? Notice there is nothing in between "Boot Sequence" and Integrated Devices": http://i290.photobucket.com/albums/l...psb33cace7.jpg Now look at the "Hard-Disk Drive Sequence" option that rarely comes up: http://i290.photobucket.com/albums/l...psc0f0d585.jpg When I did get that option, putting "Hard drive C" at the top in "Boot Sequence" didn't help me get any further into the booting process. And putting either the Seagate drive or the IBM drive at the top in "Hard-Disk Drive Sequence" didn't either: http://i290.photobucket.com/albums/l...ps8edbbf27.jpg (The other three hard drives don't show up in BIOS at all, but during the boot-up sequence it show as each is spun up). I tried every combination I could think of in "PCI IRQ Assignment": http://i290.photobucket.com/albums/l...ps24dd15fd.jpg to no avail. And in "PCI-X Slot Information" only slot 6 is occupied, which is the SCSI card. http://i290.photobucket.com/albums/l...ps62a0b031.jpg I don't think "Console Redirection" is important: http://i290.photobucket.com/albums/l...ps3b4f486c.jpg.. And in "System Security" anything relating a password is off. http://i290..photobucket.com/albums/...ps84160fdc.jpg The DELL 2600 PowerEdge motherboard features are as follows: *** Six 64-bit PCI/PCI-X slots and one 32-bit slot. Slots accept full-length cards designed for 133 MHz, 100 MHz, 66 MHz, or 33 MHz. *** An integrated VGA-compatible video subsystem with an ATI RAGE video controller. This video subsystem contains 8 MB of SDRAM video memory (nonupgradable). Maximum resolution is 1600 x 1200 x 16.7 million colors (noninterlaced). *** An integrated, dual-channel Ultra320 SCSI host adapter. *** Optional 1 x 2 backplane automatically configures the ID numbers and SCSI termination on individual hard drives, greatly simplifying drive installation. *** One integrated 10/100/1000 NIC, which provides and Ethernet interface. *** Embedded systems management circuitry that monitors operation of the system fans as well as critical system voltages and temperatures. The systems management circuitry works in conjunction with your systems management software. *** Back-panel connectors including video, keyboard, mouse, two serial, one parallel, two USB, one NIC, and one optional embedded remote access Ethernet connector. The service manual says that the supported operating systems are as follows: Microsoft Windows 2000 Server family Windows NT 4.0 Server family Red Hat Linux 7.3 or later Novell Netware 6.0 I assume this system came out before Windows XP I just wanted to confirm that XP can be installed if needed. Also, If I can get this system up and running correctly would there be any advantages of adding another processor? There is already a single VRM chip, whatever that is. But I don't know if another VRM chip would be needed if a second processor were added to the system. http://i290.photobucket.com/albums/l...ps49f8849a.jpg Also would there be any advantages to adding two more 1GB memory chips to bring the total to 6GB? (Outside of internet, DVD, MP3s, I may want to play around with ram disks and video editing). I have to look into a way to reattach the NVRAM battery so I wouldn't have to keep entering the settings whenever I want to boot up. Thanks. Darren Harris Staten Island, New York. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Bizarre issue with a Dell Poweredge 2600 | [email protected] | Dell Computers | 2 | June 22nd 08 09:07 AM |
Dell PowerEdge 2600 RAID issue | Mouse | Dell Computers | 9 | June 27th 06 09:12 AM |
RAM for PowerEdge 2600 | S W | Dell Computers | 11 | October 9th 05 05:01 PM |
No Dell Drivers for PowerEdge 2600? | B. Walker | Dell Computers | 4 | August 19th 05 04:11 PM |
scsi connectors on dell poweredge 2600 | Rusty Wright | Dell Computers | 3 | February 29th 04 10:41 AM |