A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » General Hardware & Peripherals » General
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

PSU ?



 
 
Thread Tools Display Modes
  #11  
Old July 1st 19, 06:26 PM posted to alt.comp.hardware
Paul[_28_]
external usenet poster
 
Posts: 1,467
Default PSU ?

philo wrote:
On 7/1/19 9:59 AM, John McGaw wrote:
On 6/30/2019 7:00 PM, philo wrote:
On 6/30/19 9:29 AM, John McGaw wrote:
On 6/26/2019 9:27 AM, philo wrote:
I've repaired thousands of machines and once in a while have seen a
failed power supply take out a motherboard.

Only once though have I seen the hard drives taken out.

It was with a good quality supply and I thought it was just a very
odd fluke.


Last night I talked to someone who had also had it happen ,....so
my question is:


Does any manufacturer have a supply with fully surge-protected OUTPUT?


I assumed they all did.

I, too, have had one PSU misbehave and take out a hard drive but
that was a very long time ago and with a no-name PSU. I learned my
lesson after that and now use nothing but Seasonic supplies, at
least in situations where they make a supply that will fit. Right
now the only computers I own that don't have Seasonic are my Shuttle
cubes and they are tied to the form-specific equipment. Luckily the
Shuttle PSUs have proven to be faultless also.

I don't know of any maker that installs crowbar protection on their
supplies although I believe it would take little more than a
high-current SCR a Zener diode and a few other passive components to
work the magic.



All I know is that for industrial use MOV's were everywhere and they
worked.

That said, If I try my own modifications I'll do it on a non-critical
machine first.


Will also look into Seasonic PSU's, thanks


Oh, I've use MOVs for various things but the problem is that they
aren't all that precise. Great at absorbing and dissipating lots of
power but the voltage at which they operate are vague at best. I've
used bushels of them protecting broadcast and computer equipment from
line transients but I'd be hard pressed to set them up to protect a
12V circuit from going above 13.5V where damage to a hard drive might
be expected to begin. A glance at some spec sheets suggests that using
a 12V MOV the clamping voltage might be 40+. But if you decide to give
it a shot and make it work well, please let up know.





Well, if I install MOV's and never have a HD burn out again it still
does not prove they did the trick.


I have a few other ideas though.


The person I know who lost two drives had a RAID 1 (mirrored) so he
thought he was safe.

Now I see that one possible way to build a reliable machine would be to
have each drive powered by a completely separate supply and probably
from a different manufacturer.


That said, it's been my experience in life that no matter what you plan
for, something else is going to happen!

Maybe I'll just continue doing backups because to reinstall the OS is
not a big deal...all that's important it the data


Even the RAID controller itself can fail and damage an array.
We lost two RAID5 arrays at work due to that. The first failure,
there were no "lessons learned" - the staff just restored and
pretended nothing happened. The second failure prevented hundreds of
employees from working at 2PM in the afternoon. And *that* failure,
finally got some executive oversight.

One poster on USENET, recounts how a SIL3112 failed in an interesting way.
One day, one of the two drives in RAID1 failed. Fine, the thing
continued to work with the remaining drive (as intended). However,
the files on the second drive *were three months old*. In other
words, the (software) RAID stopped mirroring *three months* before
one of the drives failed. There were no warning signs or error
messages.

It's not normal for array products like this, to carry out any sort
of audit and warn you of that sort of problem (drive mis-match
while mirroring).

All that RAID really does, is introduce more failure modes.

So even if you power the drives separately, put the drives
in different computers so the SATA ports are separated,
there is still the danger of a firmware or software failure
failing to meet functional requirements.

Paul
  #12  
Old July 2nd 19, 02:54 AM posted to alt.comp.hardware
philo
external usenet poster
 
Posts: 1,309
Default PSU ?

On 7/1/19 12:26 PM, Paul wrote:
philo wrote:
On 7/1/19 9:59 AM, John McGaw wrote:
On 6/30/2019 7:00 PM, philo wrote:
On 6/30/19 9:29 AM, John McGaw wrote:
On 6/26/2019 9:27 AM, philo wrote:
I've repaired thousands of machines and once in a while have seen
a failed power supply take out a motherboard.

Only once though have I seen the hard drives taken out.

It was with a good quality supply and I thought it was just a very
odd fluke.


Last night I talked to someone who had also had it happen ,....so
my question is:


Does any manufacturer have a supply with fully surge-protected
OUTPUT?


I assumed they all did.

I, too, have had one PSU misbehave and take out a hard drive but
that was a very long time ago and with a no-name PSU. I learned my
lesson after that and now use nothing but Seasonic supplies, at
least in situations where they make a supply that will fit. Right
now the only computers I own that don't have Seasonic are my
Shuttle cubes and they are tied to the form-specific equipment.
Luckily the Shuttle PSUs have proven to be faultless also.

I don't know of any maker that installs crowbar protection on their
supplies although I believe it would take little more than a
high-current SCR a Zener diode and a few other passive components
to work the magic.



All I know is that for industrial use MOV's were everywhere and they
worked.

That said, If I try my own modifications I'll do it on a
non-critical machine first.


Will also look into Seasonic PSU's, thanks

Oh, I've use MOVs for various things but the problem is that they
aren't all that precise. Great at absorbing and dissipating lots of
power but the voltage at which they operate are vague at best. I've
used bushels of them protecting broadcast and computer equipment from
line transients but I'd be hard pressed to set them up to protect a
12V circuit from going above 13.5V where damage to a hard drive might
be expected to begin. A glance at some spec sheets suggests that
using a 12V MOV the clamping voltage might be 40+. But if you decide
to give it a shot and make it work well, please let up know.





Well, if I install MOV's and never have a HD burn out again it still
does not prove they did the trick.


I have a few other ideas though.


The person I know who lost two drives had a RAID 1 (mirrored) so he
thought he was safe.

Now I see that one possible way to build a reliable machine would be
to have each drive powered by a completely separate supply and
probably from a different manufacturer.


That said, it's been my experience in life that no matter what you
plan for, something else is going to happen!

Maybe I'll just continue doing backups because to reinstall the OS is
not a big deal...all that's important it the data


Even the RAID controller itself can fail and damage an array.
We lost two RAID5 arrays at work due to that. The first failure,
there were no "lessons learned" - the staff just restored and
pretended nothing happened. The second failure prevented hundreds of
employees from working at 2PM in the afternoon. And *that* failure,
finally got some executive oversight.

One poster on USENET, recounts how a SIL3112 failed in an interesting way.
One day, one of the two drives in RAID1 failed. Fine, the thing
continued to work with the remaining drive (as intended). However,
the files on the second drive *were three months old*. In other
words, the (software) RAID stopped mirroring *three months* before
one of the drives failed. There were no warning signs or error
messages.

It's not normal for array products like this, to carry out any sort
of audit and warn you of that sort of problem (drive mis-match
while mirroring).

All that RAID really does, is introduce more failure modes.

So even if you power the drives separately, put the drives
in different computers so the SATA ports are separated,
there is still the danger of a firmware or software failure
failing to meet functional requirements.

Â*Â* Paul




Maybe I'll just quit worrying about it and continue to to backups
frequently
  #13  
Old July 2nd 19, 02:55 AM posted to alt.comp.hardware
philo
external usenet poster
 
Posts: 1,309
Default PSU ?

On 7/1/19 10:38 AM, John McGaw wrote:
On 7/1/2019 11:20 AM, philo wrote:
On 7/1/19 9:59 AM, John McGaw wrote:
On 6/30/2019 7:00 PM, philo wrote:
On 6/30/19 9:29 AM, John McGaw wrote:
On 6/26/2019 9:27 AM, philo wrote:
I've repaired thousands of machines and once in a while have seen
a failed power supply take out a motherboard.

Only once though have I seen the hard drives taken out.

It was with a good quality supply and I thought it was just a very
odd fluke.


Last night I talked to someone who had also had it happen ,....so
my question is:


Does any manufacturer have a supply with fully surge-protected
OUTPUT?


I assumed they all did.

I, too, have had one PSU misbehave and take out a hard drive but
that was a very long time ago and with a no-name PSU. I learned my
lesson after that and now use nothing but Seasonic supplies, at
least in situations where they make a supply that will fit. Right
now the only computers I own that don't have Seasonic are my
Shuttle cubes and they are tied to the form-specific equipment.
Luckily the Shuttle PSUs have proven to be faultless also.

I don't know of any maker that installs crowbar protection on their
supplies although I believe it would take little more than a
high-current SCR a Zener diode and a few other passive components
to work the magic.



All I know is that for industrial use MOV's were everywhere and they
worked.

That said, If I try my own modifications I'll do it on a
non-critical machine first.


Will also look into Seasonic PSU's, thanks

Oh, I've use MOVs for various things but the problem is that they
aren't all that precise. Great at absorbing and dissipating lots of
power but the voltage at which they operate are vague at best. I've
used bushels of them protecting broadcast and computer equipment from
line transients but I'd be hard pressed to set them up to protect a
12V circuit from going above 13.5V where damage to a hard drive might
be expected to begin. A glance at some spec sheets suggests that
using a 12V MOV the clamping voltage might be 40+. But if you decide
to give it a shot and make it work well, please let up know.





Well, if I install MOV's and never have a HD burn out again it still
does not prove they did the trick.


I have a few other ideas though.


The person I know who lost two drives had a RAID 1 (mirrored) so he
thought he was safe.

Now I see that one possible way to build a reliable machine would be
to have each drive powered by a completely separate supply and
probably from a different manufacturer.


That said, it's been my experience in life that no matter what you
plan for, something else is going to happen!

Maybe I'll just continue doing backups because to reinstall the OS is
not a big deal...all that's important it the data


There is no substitute for backups. No matter what. I am quite paranoid
about protecting my primary machine. As I write this it is doing its
monthly backup which will go into the bank's vault this afternoon --
there are three portable drives cycling through these backups. Every
evening it does a full backup to my elderly WHS and at 1AM it did a
backup to one of my redundant Drobo NAS units. Oh, and as the mood
strikes me I do a system disk image to a series of portable SSD units
that are kept in a media safe here at home in case I need to restore a
bootable image. I have been burned too many times by seemingly random
glitches. This level of backup would be overkill for most people but I
believe that any user who doesn't have at least two levels of backup,
one of them offsite but under his/her direct control, is a fool and
probably deserves whatever comes their way.



I back up often so I guess I will quit worrying about this
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 08:11 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.