If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Resource Allocation Conflict
Does anyone remember how to get past hardware errors...I installed a
linksys card in the only pci slot of this legend 402 cd (pb 600 mb, phoenix bios ver 1.17, win95 1st edition), and moved the snd/modem card to the center isa slot. I get a resource allocation error pci device 0098 at slot 3 when I boot the machine. Hiting F1 resumes the boot with no problem. Is there a registry problem? Ben thanks for the intel 133 cpu it works great... mc |
#2
|
|||
|
|||
Resource Allocation Conflict
On Sep 6, 1:46*pm, mc wrote:
Does anyone remember how to get past hardware errors...I installed a linksys card in the only pci slot of this legend 402 cd (pb 600 mb, phoenix bios ver 1.17, win95 1st edition), and moved the snd/modem card to the center isa slot. I get a resource allocation error pci device 0098 at slot 3 when I boot the machine. Hiting F1 resumes the boot with no problem. Is there a registry problem? Ben thanks for the *intel 133 cpu it works great... mc Did you check the device resources in device manager You may want to change the irq http://www.computerhope.com/issues/ch000197.htm or sometimes prayer helps |
#3
|
|||
|
|||
Resource Allocation Conflict
On Sep 6, 8:10*pm, metronid wrote:
On Sep 6, 1:46*pm, mc wrote: Does anyone remember how to get past hardware errors...I installed a linksys card in the only pci slot of this legend 402 cd (pb 600 mb, phoenix bios ver 1.17, win95 1st edition), and moved the snd/modem card to the center isa slot. I get a resource allocation error pci device 0098 at slot 3 when I boot the machine. Hiting F1 resumes the boot with no problem. Is there a registry problem? Ben thanks for the *intel 133 cpu it works great... mc Did you check the device resources in device manager You may want to change the irq http://www.computerhope.com/issues/ch000197.htm or sometimes prayer helps The IRQ is giving me a hard time, I removed the linksys card, and now I get an IRQ conflict at boot. The settings are all the same as my PB994 legend where both com1 and com3 use IRQ4, so I'm not sure where the IRQ conflict is coming from. Does anyone have the phoenix agoura 4.04 version 1.18 bios in their archives? If so could you e-mail it to me? thanks mc |
#4
|
|||
|
|||
Resource Allocation Conflict
"mc" wrote in message ... On Sep 6, 8:10 pm, metronid wrote: On Sep 6, 1:46 pm, mc wrote: Does anyone remember how to get past hardware errors...I installed a linksys card in the only pci slot of this legend 402 cd (pb 600 mb, phoenix bios ver 1.17, win95 1st edition), and moved the snd/modem card to the center isa slot. I get a resource allocation error pci device 0098 at slot 3 when I boot the machine. Hiting F1 resumes the boot with no problem. Is there a registry problem? Ben thanks for the intel 133 cpu it works great... mc Did you check the device resources in device manager You may want to change the irq http://www.computerhope.com/issues/ch000197.htm or sometimes prayer helps The IRQ is giving me a hard time, I removed the linksys card, and now I get an IRQ conflict at boot. The settings are all the same as my PB994 legend where both com1 and com3 use IRQ4, so I'm not sure where the IRQ conflict is coming from. Does anyone have the phoenix agoura 4.04 version 1.18 bios in their archives? If so could you e-mail it to me? thanks mc Put the sound/modem card back in the original slot if you have not already done so... otherwise, check to see if your bios as an "auto" allocation option |
#5
|
|||
|
|||
Resource Allocation Conflict
As a last resort, remove the CMOS battery and let the CMOS settings become
in-valid. (They are not sick invalids.) Then start again with placement of cards, after entering in valid settings. Write down the hard drive settings, because these old system BIOSes often do not autodetect the drive geometry. .... Ben Myers On Mon, 8 Sep 2008 18:49:59 -0500, "philo" wrote: "mc" wrote in message ... On Sep 6, 8:10 pm, metronid wrote: On Sep 6, 1:46 pm, mc wrote: Does anyone remember how to get past hardware errors...I installed a linksys card in the only pci slot of this legend 402 cd (pb 600 mb, phoenix bios ver 1.17, win95 1st edition), and moved the snd/modem card to the center isa slot. I get a resource allocation error pci device 0098 at slot 3 when I boot the machine. Hiting F1 resumes the boot with no problem. Is there a registry problem? Ben thanks for the intel 133 cpu it works great... mc Did you check the device resources in device manager You may want to change the irq http://www.computerhope.com/issues/ch000197.htm or sometimes prayer helps The IRQ is giving me a hard time, I removed the linksys card, and now I get an IRQ conflict at boot. The settings are all the same as my PB994 legend where both com1 and com3 use IRQ4, so I'm not sure where the IRQ conflict is coming from. Does anyone have the phoenix agoura 4.04 version 1.18 bios in their archives? If so could you e-mail it to me? thanks mc Put the sound/modem card back in the original slot if you have not already done so... otherwise, check to see if your bios as an "auto" allocation option |
#6
|
|||
|
|||
Resource Allocation Conflict
On Sep 8, 8:19*pm, Ben Myers
wrote: As a last resort, remove the CMOS battery and let the CMOS settings become in-valid. (They are not sick invalids.) * Then start again with placement of cards, after entering in valid settings. *Write down the hard drive settings, because these old system BIOSes often do not autodetect the drive geometry. ... Ben Myers On Mon, 8 Sep 2008 18:49:59 -0500, "philo" wrote: "mc" wrote in message .... On Sep 6, 8:10 pm, metronid wrote: On Sep 6, 1:46 pm, mc wrote: Does anyone remember how to get past hardware errors...I installed a linksys card in the only pci slot of this legend 402 cd (pb 600 mb, phoenix bios ver 1.17, win95 1st edition), and moved the snd/modem card to the center isa slot. I get a resource allocation error pci device 0098 at slot 3 when I boot the machine. Hiting F1 resumes the boot with no problem. Is there a registry problem? Ben thanks for the intel 133 cpu it works great... mc Did you check the device resources in device manager You may want to change the irq http://www.computerhope.com/issues/ch000197.htm or sometimes prayer helps The IRQ is giving me a hard time, I removed the linksys card, and now I get an IRQ conflict at boot. The settings are all the same as my PB994 legend where both com1 and com3 use IRQ4, so I'm not sure where the IRQ conflict is coming from. Does anyone have the phoenix agoura 4.04 version 1.18 bios in their archives? If so could you e-mail it to me? thanks mc Put the sound/modem card back in the original slot if you have not already done so... otherwise, check to see if your bios as an "auto" allocation option- Hide quoted text - - Show quoted text - Ben I have not tried pulling the jumper yet to disconnect the battery, i suspect the battery may be old (1994). Does any one know which jumper pin is + or - on this board for an external battery. I only know to connect pins 1 and 4 , so I will need to pick up some type of connector to build an external battery. I'm still trying to find the agoura version 1.18 if anyone has this flash bios saved on a floppy?I did notice this bios chip is removable, so what other options would I have for using another chip (beyond my current knowledge)? mc |
#7
|
|||
|
|||
Resource Allocation Conflict
On Sep 14, 11:18*am, mc wrote:
On Sep 8, 8:19*pm, Ben Myers wrote: As a last resort, remove the CMOS battery and let the CMOS settings become in-valid. (They are not sick invalids.) * Then start again with placement of cards, after entering in valid settings. *Write down the hard drive settings, because these old system BIOSes often do not autodetect the drive geometry. ... Ben Myers On Mon, 8 Sep 2008 18:49:59 -0500, "philo" wrote: "mc" wrote in message .... On Sep 6, 8:10 pm, metronid wrote: On Sep 6, 1:46 pm, mc wrote: Does anyone remember how to get past hardware errors...I installed a linksys card in the only pci slot of this legend 402 cd (pb 600 mb, phoenix bios ver 1.17, win95 1st edition), and moved the snd/modem card to the center isa slot. I get a resource allocation error pci device 0098 at slot 3 when I boot the machine. Hiting F1 resumes the boot with no problem. Is there a registry problem? Ben thanks for the intel 133 cpu it works great... mc Did you check the device resources in device manager You may want to change the irq http://www.computerhope.com/issues/ch000197.htm or sometimes prayer helps The IRQ is giving me a hard time, I removed the linksys card, and now I get an IRQ conflict at boot. The settings are all the same as my PB994 legend where both com1 and com3 use IRQ4, so I'm not sure where the IRQ conflict is coming from. Does anyone have the phoenix agoura 4.04 version 1.18 bios in their archives? If so could you e-mail it to me? thanks mc Put the sound/modem card back in the original slot if you have not already done so... otherwise, check to see if your bios as an "auto" allocation option- Hide quoted text - - Show quoted text - Ben I have not tried pulling the jumper yet to disconnect the battery, i suspect the battery may be old (1994). Does any one know which jumper pin is + or - on this board for an external battery. I only know to connect pins 1 and 4 , so I will need to pick up some type of connector to build an external battery. I'm still trying to find the agoura version 1.18 if anyone has this flash bios saved on a floppy?I did notice this bios chip is removable, so what other options would I have for using another chip (beyond my current knowledge)? mc- Hide quoted text - - Show quoted text - Uses a 3.0 volt lithium battery, but can be replaced with a 3.6 volt. Remove the jumper on pins 3-4 of J29 (Jbatt) battery connector. The battery connector is keyed and will only go in one way. pin 1= +3 volts pin 2= key pin 3= on-board battery select pin 4= ground |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Memory allocation | Samuel Shulman | General | 6 | December 17th 07 10:18 PM |
Recovery Allocation Size? | NapalmHeart | Compaq Computers | 3 | December 29th 06 01:09 AM |
problems installing radeon 9800 pro ( resource conflict, code 12in strange memory range) | Niklas Schaffrath | Ati Videocards | 8 | July 11th 05 11:08 PM |
File allocation | perrera | General | 5 | November 11th 03 04:21 PM |
Resource Conflict PnP Device CD | sammy | General Hardware | 0 | October 22nd 03 11:41 AM |