If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
I guess you don't know how to read. I wasn't flaming the enermax
Quote: The enermax wasn't a bad unit Unquote The 600W POS (as you put it) is working fine with a 450+watt load as calculated from the website you provided. Not bad for 24$ "Philip Callan" wrote in message news:VyZXb.525591$ts4.337603@pd7tw3no... -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Leadfoot wrote: | "Darkfalz" wrote in message | |Any good brand 300-400 watt should be fine. A good brand 250 watt will |perform better than a generic 400 watt, so obviously the most important |thing is to get a reputable brand (AOpen, Antec etc.). | | | Bull****!!! | | I just went from an enermax EG-431 (79$ 2-3 years ago) that was choking when | I ran 3dmark03 with an 2500xp being run as a 3200xp on an NF-7S to a 25$ | 600W power supply that runs 3dmark03 just fine at 11X200. Looped for 8 | hours straight in test mode. The enermax wasn't a bad unit, its 15 amps on | the 12v line simply wasn't enough. 24 amps with the Lead Power did the | trick. having a 9800, 3 7200rpm HD, 2 dvd's and 4 80mm fans with some other | misc stuff didn't help. | | http://tinyurl.com/2czrp Hmm, 2-3 years ago with processors and video cards pulling what they do, no wonder it was adequate (but its still crap compared to a brand name) First off your EG-431, is probably a lesser quality variant of this one (the EG451P-VE) http://www.pcstats.com/articleview.c...eid=409&page=4 Older review (which is very favorable, but compared to todays PSU , and the new ATX specification, its a DOG) The important part is he Operation Temperature ~ 0oC~25oCfor full rating of load, ~ decrease to zero Watts O/P at 70oC Okay, that particular PSU does not use seperate voltage regulation on each channel, so a heavy pull on your 12v rail will drag your others down, and lower their true output you get that? It will give that 15A on your 12v rail when its at 25 degrees Celsius. Have you felt 25C ? its COOL, seeing as your body temp is like 37C, when was (other than in the 15 seconds AFTER a POST) the last time you ever had COOL air coming from your PSU? Every degree of heat it rises, it LOSES efficiency, until it finally cant provide any of the rails proper current, let along all of them. Then go he http://www.jscustompcs.com/power_supply/ Fire in your CPU/RAM/HD settings (I didnt know your RAM or extra peripherals except the FANS, but I came up with 353W as your recommended PSU. That 4 year old powersupply, from the Celeron / Pentium 2 era, trying to power a r9800 and a 2500xp (overclocked even! more draw on the rails) No wonder you had problems. The Enermax PSU has 0 problems, other than it was designed for far less hungry devices and motherboards than todays computers, you putting a PSU that couldnt realistically provide the current you needed, does not mean that your POS 600w generic is better than an Enermax. Philip -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (MingW32) iD8DBQFAMGU85sKixANmEMgRAvO/AJ0T8i97w+UnXYCibyCI+R3jOaq/CQCeMUNt sfeL3pTGLlGLyEkCVSEogX4= =nDAC -----END PGP SIGNATURE----- |
#22
|
|||
|
|||
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1 Leadfoot wrote: | I guess you don't know how to read. I wasn't flaming the enermax | | Quote: | | The enermax wasn't a bad unit | | Unquote | | The 600W POS (as you put it) is working fine with a 450+watt load as | calculated from the website you provided. Not bad for 24$ I guess you suffer the syndrome you accuse me of: Quote: | Older review (which is very favorable, but compared to todays PSU , and | the new ATX specification, its a DOG) or | The Enermax PSU has 0 problems, other than it was designed for far less | hungry devices and motherboards than todays computers, you putting a PSU | that couldnt realistically provide the current you needed, does not mean | that your POS 600w generic is better than an Enermax. I never said you were flaming the enermax, but when "Darkfalz" wrote: | |Any good brand 300-400 watt should be fine. A good brand 250 watt will | |perform better than a generic 400 watt, so obviously the most important | |thing is to get a reputable brand (AOpen, Antec etc.). You cried "Bull****" and then went on to describe how you took a 3yr old + powersupply with an inadequate 12v rail, tried to hook a newer spec system drying far more load, and had problems, but when switching to your generic 600w PSU, everything was fine. Implying that the 600w was better than the Enermaxx Thats the part I was contesting. Generic PSU's will not perform better than their Brand counterparts *of the same Wattage* Simply because the machine 'runs' is not enough to say that its 'fine' Consider why Generic PSU's simply add up their maximum load which it cant realistically sustain for *ANY* period of time, since as soon as they break 25C they start to degrade in performance, and no longer output the W advertised, if they ever did. Brand PSU's are starting to provide seperate voltage regulation for EACH rail (3.3/5v/12v) so that large draws on any one rail it doesnt destabilize the other rails. In probably 95% of generic PSU's, the 3.3 and 5v lines are together and although their voltage 'ripple' may stay within ATX boundaries, its 5/10% are a far cry from the tolerated 3/5% on Brand PSU's (Antec, Enermax, PP&C, Thermaltake etc) I just dont like people *ever* giving the advice to get a Generic PSU, since its one of the most critical parts in a system, and especially not these ones adertised using stupid wattages. A good power supply should perform within regulation under maximum load conditions (that means that even when I pull its maximum rated wattage from it, it should still not vary the rails beyond ATX tolerances) That PSU is 600w in a fairy tale world where nothing exceeds 25C and doesnt ask it to provide 600w true output for more than a few seconds before dying. Brand PSU's are always rated to what their TRUE Maximum Output Wattage is (not theoretical) (sustained for 15-30 minutes depending on manufacturer) and *THEN* under-rated, ie, if it pushes 395w, its not a 400w its a 330w, if it pushes 500, its sold as 425 or something, by doing this, the assure that even under maximum RATED load, your voltage regulation is still within tolerances. As with most 'Generic' products, you get what you pay for. Personally I think the idea of trusting a few hundred dollars worth of hardware or more to a TWENTY-FOUR dollar PSU is asking for trouble. You should consider running MBM or the like, and logging your voltages for a few days, during all sorts of tasks, and watch for ripples. Philip -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (MingW32) iD8DBQFAMMQU5sKixANmEMgRAgGCAKCbz+qSPLX66mK4l/kxTarqZ46cVACg5WQL cLL/ZzMPKQv9f9ZuPSKWD9o= =NP+T -----END PGP SIGNATURE----- |
#23
|
|||
|
|||
"Philip Callan" wrote in message news:gu3Yb.530752$ts4.251398@pd7tw3no... -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Leadfoot wrote: | I guess you don't know how to read. I wasn't flaming the enermax | | Quote: | | The enermax wasn't a bad unit | | Unquote | | The 600W POS (as you put it) is working fine with a 450+watt load as | calculated from the website you provided. Not bad for 24$ I guess you suffer the syndrome you accuse me of: Quote: | Older review (which is very favorable, but compared to todays PSU , and | the new ATX specification, its a DOG) or | The Enermax PSU has 0 problems, other than it was designed for far less | hungry devices and motherboards than todays computers, you putting a PSU | that couldnt realistically provide the current you needed, does not mean | that your POS 600w generic is better than an Enermax. I never said you were flaming the enermax, but when "Darkfalz" wrote: | |Any good brand 300-400 watt should be fine. A good brand 250 watt will | |perform better than a generic 400 watt, so obviously the most important | |thing is to get a reputable brand (AOpen, Antec etc.). You cried "Bull****" and then went on to describe how you took a 3yr old + powersupply with an inadequate 12v rail, tried to hook a newer spec system drying far more load, and had problems, but when switching to your generic 600w PSU, everything was fine. Implying that the 600w was better than the Enermaxx I was saying bull**** on making sure to buy a brand name PSU at 4 times the price. Thats the part I was contesting. Generic PSU's will not perform better than their Brand counterparts *of the same Wattage* Simply because the machine 'runs' is not enough to say that its 'fine' Consider why Generic PSU's simply add up their maximum load which it cant realistically sustain for *ANY* period of time, since as soon as they break 25C they start to degrade in performance, and no longer output the W advertised, if they ever did. Brand PSU's are starting to provide seperate voltage regulation for EACH rail (3.3/5v/12v) so that large draws on any one rail it doesnt destabilize the other rails. In probably 95% of generic PSU's, the 3.3 and 5v lines are together and although their voltage 'ripple' may stay within ATX boundaries, its 5/10% are a far cry from the tolerated 3/5% on Brand PSU's (Antec, Enermax, PP&C, Thermaltake etc) About 90% or more of the branded PSU's have the 3.3 and 5V lines together also. I think you can count the number where all three are separate on one hand and usuallly it's the top end of the product line. They get quite expensive I just dont like people *ever* giving the advice to get a Generic PSU, since its one of the most critical parts in a system, and especially not these ones adertised using stupid wattages. A good power supply should perform within regulation under maximum load conditions (that means that even when I pull its maximum rated wattage from it, it should still not vary the rails beyond ATX tolerances) That PSU is 600w in a fairy tale world where nothing exceeds 25C and doesnt ask it to provide 600w true output for more than a few seconds before dying. My system is at 32C at the moment. I don't think I'm going to draw more than 540W (600W- 10%) until AMD reaches the K10 generation (assuming AMD64 =K8) and I'm not really interested in trying to get 600W out of it. As long as it handles 450-500W for the very low price of TWENTY-FOUR DOLLARS. I'm happy Brand PSU's are always rated to what their TRUE Maximum Output Wattage is (not theoretical) (sustained for 15-30 minutes depending on manufacturer) and *THEN* under-rated, ie, if it pushes 395w, its not a 400w its a 330w, if it pushes 500, its sold as 425 or something, by doing this, the assure that even under maximum RATED load, your voltage regulation is still within tolerances. As with most 'Generic' products, you get what you pay for. Personally I think the idea of trusting a few hundred dollars worth of hardware or more to a TWENTY-FOUR dollar PSU is asking for trouble. You should consider running MBM or the like, and logging your voltages for a few days, during all sorts of tasks, and watch for ripples. Ahh you want me to use MBM in conjuction with the motherboard sensor to determine what the regulation/ripple is of the power supply??? I have my doubts about your technical ability if you really believe this You don't do a SERIOUS test of a PSU with a motherboard sensor. You use a voltmeter. Even better would be an Oscilloscope. I COULD do a voltmeter test if I feel like spending the time to set it up and write down the results But just to humor you I did a run of 3DMark03 with the MBM log turned on. The highest percentage I got for regulation (12/3.3/5vdc) was 1.6%. I would have liked to have done this over an extended period of time but there is a limit of 1000 entries in the MBM log. I set it for 6 seconds Formula used was Vhigh - Vlow / VAvg I've erased the results but I can redo and post it someplace it if you'd like and change the test conditions if you have a suggestion that makes sense to me. Anyway I'll laugh all the way to the bank BTW the temp inside my case is about 32 C. Even though its February its a little hot here in Phoenix. Philip -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (MingW32) iD8DBQFAMMQU5sKixANmEMgRAgGCAKCbz+qSPLX66mK4l/kxTarqZ46cVACg5WQL cLL/ZzMPKQv9f9ZuPSKWD9o= =NP+T -----END PGP SIGNATURE----- |
#24
|
|||
|
|||
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1 Leadfoot wrote: | I was saying bull**** on making sure to buy a brand name PSU at 4 times the | price. Where did this 4x figure come from? it wasnt in the OP. Okay, you obviously believe that paying 1000 dollars for a car that gets you from A to B provided you have no more than # number of friends, and provided the road is perfectly smooth, as opposed to paying 3-4000 for a Truck that not only carries you, but 8 of your friends, up the side of a mountain and through the mud. | About 90% or more of the branded PSU's have the 3.3 and 5V lines together | also. I think you can count the number where all three are separate on one | hand and usuallly it's the top end of the product line. They get quite | expensive Its usually the 'top' end of the product line since its what all QUALITY ~ psu's should start doing, especially given that a lot of newer devices can really yank the heck out of a rail and destabilize the rest. Its called Quality. You end up paying for it. | My system is at 32C at the moment. I don't think I'm going to draw more | than 540W (600W- 10%) until AMD reaches the K10 generation (assuming AMD64 | =K8) and I'm not really interested in trying to get 600W out of it. As long | as it handles 450-500W for the very low price of TWENTY-FOUR DOLLARS. I'm | happy Ok, so your saying for $24 bucks, that your happy with your 600 W PSU, provided you dont pull more than 450-500W from it (thats called OVERRATING the PSU) I never said you couldnt be happy, I just asked that you stop saying that people should buy Generic. For the cost of my Sonata case (170CAN) I got a TruePower 380S in it, I briefly contemplated replacing with a higher 'wattage' but after looking into it, I found that unlike the 600w that is adequate to 450-500, my 380w is good to about 430w under max load. I'm quite happy with my PSU as well. | Ahh you want me to use MBM in conjuction with the motherboard sensor to | determine what the regulation/ripple is of the power supply??? I have my | doubts about your technical ability if you really believe this Your welcome to doubt my ability, thats the benefit of a medium where I can say something, and your not REQUIRED to believe me. | | You don't do a SERIOUS test of a PSU with a motherboard sensor. You use a | voltmeter. Even better would be an Oscilloscope. I COULD do a voltmeter test | if I feel like spending the time to set it up and write down the results I didnt equate it with a 'serious' test, just a fairly simple test that anyone (*without* a voltmeter or oscilliscope) could do, I wasnt aware you were that technically competent. And yes I know you are going to get fluctuations simply beause of trace resistance, and that they arent the most accurate. But in areas when taxing the system loads a rail to high, ~ its surely sensitive enough to determine the drop out on other rails. | But just to humor you I did a run of 3DMark03 with the MBM log turned on. | The highest percentage I got for regulation (12/3.3/5vdc) was 1.6%. I would | have liked to have done this over an extended period of time but there is a | limit of 1000 entries in the MBM log. I set it for 6 seconds Formula used | was Vhigh - Vlow / VAvg I'm glad to hear it, I wasnt posting expecting you to come back saying 'OMG you were dead on" you'd said that you weren't having problems, so I didnt expect you to come back with odd figures or anything, I was just letting you know that although wattage/load may *NOT* be major factors to you, ripple *should* be something your concerned with. Philip -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (MingW32) iD8DBQFAMU9r5sKixANmEMgRAvnJAJ98a0jDPK2HDAaU1PHyy2 N0J/7yhQCglnA0 qZS3YHw85t15TS0jdAPsV2k= =iK9k -----END PGP SIGNATURE----- |
#25
|
|||
|
|||
On Mon, 16 Feb 2004 23:16:51 +0000, Philip Callan wrote:
Leadfoot wrote: My system is at 32C at the moment. I don't think I'm going to draw more than 540W (600W- 10%) until AMD reaches the K10 generation (assuming AMD64=K8) and I'm not really interested in trying to get 600W out of it. As long as it handles 450-500W for the very low price of TWENTY-FOUR DOLLARS. I'm happy Ok, so your saying for $24 bucks, that your happy with your 600 W PSU, provided you dont pull more than 450-500W from it (thats called OVERRATING the PSU) I never said you couldnt be happy, I just asked that you stop saying that people should buy Generic. Sorry, but I would also say buy generic. But I would also say always buy bigger than what you think you need, generic or not. I'm not sure, but genereics may or may not have a bigger failure rate, but it isn't twice as high, and nowhere near the 3-6 times more you will pay for name brand. I'm happy with all my cheapass PSU's Ive bought over the last 5 years for personal use. They are ALL still running, except one that burned up in a fire (not started by computer:-)). Over the last 10 years I've probably built more than 100 systems and generic PSU's was the least of my problems. So yes, I say buy generic too. -- Abit KT7-Raid (KT133) Tbred B core CPU @2400MHz (24x100FSB) http://mysite.verizon.net/res0exft/cpu.htm |
#26
|
|||
|
|||
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1 Wes Newell wrote: | | Sorry, but I would also say buy generic. But I would also say always buy | bigger than what you think you need, generic or not. I'm not sure, but | genereics may or may not have a bigger failure rate, but it isn't twice as | high, and nowhere near the 3-6 times more you will pay for name brand. Well, at least this one contains some good advice 'But I would also say always buy bigger than what you think you need, generic or not' I dont know where the 'twice as high' MTBF comes into play, I never made that claim. And as for the 3-6 times figure, yes, you *could* theoretically pay 6 times more for a Brand PSU vs a Generic. Like that $24 600w vs a *REAL* 550w like this: | http://www.newegg.com/app/ViewProduc...=BROWSE&depa=1 for woo, $100 US, so 4x the cost of a cheap PSU, maybe twice the cost of a middle-line. Philip -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (MingW32) iD8DBQFAMWZ+5sKixANmEMgRApzgAJ0ZlsD9/DiHPQioZ3KIzaNySJLyNwCfUxzE whKj2M1nkgABMO2buytYgWE= =bcBN -----END PGP SIGNATURE----- |
#27
|
|||
|
|||
i suppose you missed this one:
http://www.newegg.com/app/viewProduc...103-438&depa=1 only $250! 660W "Philip Callan" wrote in message news:XDdYb.536092$ts4.384514@pd7tw3no... -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Wes Newell wrote: | | Sorry, but I would also say buy generic. But I would also say always buy | bigger than what you think you need, generic or not. I'm not sure, but | genereics may or may not have a bigger failure rate, but it isn't twice as | high, and nowhere near the 3-6 times more you will pay for name brand. Well, at least this one contains some good advice 'But I would also say always buy bigger than what you think you need, generic or not' I dont know where the 'twice as high' MTBF comes into play, I never made that claim. And as for the 3-6 times figure, yes, you *could* theoretically pay 6 times more for a Brand PSU vs a Generic. Like that $24 600w vs a *REAL* 550w like this: | http://www.newegg.com/app/ViewProduc...=BROWSE&depa=1 for woo, $100 US, so 4x the cost of a cheap PSU, maybe twice the cost of a middle-line. Philip -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (MingW32) iD8DBQFAMWZ+5sKixANmEMgRApzgAJ0ZlsD9/DiHPQioZ3KIzaNySJLyNwCfUxzE whKj2M1nkgABMO2buytYgWE= =bcBN -----END PGP SIGNATURE----- |
#28
|
|||
|
|||
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1 KJ wrote: | i suppose you missed this one: | http://www.newegg.com/app/viewProduc...103-438&depa=1 | | only $250! | 660W | No I didn't. But comparing Price differences between a BRAND PSU, that actually delivers the advertised wattage, and can do so for extended periods, without ripple, is unfair. That 24$ 600w would be sold by most Brand companies as a 400w or 380w at most. It cant realistically provide 600w, even the person using it said as much, that they fell 'safe' about it provided he doesnt pull more than the 450-500w he currently consumes. Please stop comparing the price of a 1965 Corvair to a 2004 BMW, they arent the same magnitude of quality. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (MingW32) iD8DBQFAMXtm5sKixANmEMgRAqV2AJ4kua2F9kDec7HIp6L3ed 8mXq62nACeNfq3 JXmTCT1RCzDJ4oTtE50btac= =xlWd -----END PGP SIGNATURE----- |
#29
|
|||
|
|||
Hi Leadfoot,
I wish you luck but a $25 600W PS is like putting a junk yard engine in an Indy 500 car s. The power supply is the heart of a good system. One should *never* compromise on the PS. -- Tally Ho! Ed "Leadfoot" wrote in message news:KZXXb.4483$hE.2344@fed1read07... "Darkfalz" wrote in message ... "TboXx" wrote in message m... I know this is a motherboard forum but im guessing you all would know if your here anyway. Is there an easy way to tell what watt power supply i should get? or any site you could direct me to, Thanks Any good brand 300-400 watt should be fine. A good brand 250 watt will perform better than a generic 400 watt, so obviously the most important thing is to get a reputable brand (AOpen, Antec etc.). Bull****!!! I just went from an enermax EG-431 (79$ 2-3 years ago) that was choking when I ran 3dmark03 with an 2500xp being run as a 3200xp on an NF-7S to a 25$ 600W power supply that runs 3dmark03 just fine at 11X200. Looped for 8 hours straight in test mode. The enermax wasn't a bad unit, its 15 amps on the 12v line simply wasn't enough. 24 amps with the Lead Power did the trick. having a 9800, 3 7200rpm HD, 2 dvd's and 4 80mm fans with some other misc stuff didn't help. http://tinyurl.com/2czrp |
#30
|
|||
|
|||
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1 Philip Callan wrote: | KJ wrote: | | | i suppose you missed this one: | | | http://www.newegg.com/app/viewProduc...103-438&depa=1 | | | | only $250! | | 660W | | | | No I didn't. But comparing Price differences between a BRAND PSU, that | actually delivers the advertised wattage, and can do so for extended | periods, without ripple, is unfair. | I should qualify this, 'without *ATX specification acceptable or BETTER* ripple' | That 24$ 600w would be sold by most Brand companies as a 400w or 380w at | most. It cant realistically provide 600w, even the person using it said | as much, that they fell 'safe' about it provided he doesnt pull more | than the 450-500w he currently consumes. | | Please stop comparing the price of a 1965 Corvair to a 2004 BMW, they | arent the same magnitude of quality. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (MingW32) iD8DBQFAMX6e5sKixANmEMgRAsTlAKCLqQACrF4LFdG7vYiADN VU9DQLsQCgi018 XRIC0YHk6MCajFKeWuqg92E= =nd0H -----END PGP SIGNATURE----- |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
my new mobo o/c's great | rockerrock | Overclocking AMD Processors | 9 | June 30th 04 08:17 PM |
Really low 1000-1100 RPM reading on Power Supply Fan | Hupjack | Homebuilt PC's | 6 | April 25th 04 09:49 AM |
Power supply question | Frank Kirk | General | 5 | April 18th 04 11:36 AM |
PSU Fans | Muttly | General | 16 | February 13th 04 10:42 PM |
NF7-S power up problem | Jeff Green | Abit Motherboards | 9 | January 18th 04 07:06 PM |