If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
"Power calibration failed." with Traxdata 48/12/48 and burnatonce
Hello,
I've got a problem burning CDs with my Traxdata 48/12/48 and burnatonce (as well with Nero) under WinXP Pro SP1, just after starting the burning, it stops, the log i get is as following: SPTILOCK:0,1,0: CD-RW CDR-5W48 Rev: VSG3 Starting write at speed 48... Turning BURN-Proof on Executing power calibration... ?: I/O error. : scsi sendcmd: retryable error CDB: 54 01 00 00 00 00 00 00 00 00 status: 0x0 (GOOD STATUS) cmd finished after 5.370s timeout 180s ERROR: Power calibration failed. ERROR: Use option --force to ignore this error. ERROR: Writing failed. I have got a SCSI card mounted in my system but it is disabled, and the CD-Writer is an IDE device. I've searched quite a while with Google and in the Usenet, this problem seems to appear as well under Linux, but I don't think the most common answer "clean the laser lense" does apply to my problem, because the Writer worked fine in my system until I killed my bios and then got a new mainboard and as well reinstalled WinXP. Is there anyone with an idea how to solve my problem? Thanks, Lars |
#2
|
|||
|
|||
SPTILOCK:0,1,0: CD-RW CDR-5W48 Rev: VSG3
Disable the STPI interface. It's too new in Burnatonce. Use ASPI 4.60 to access drives. |
#3
|
|||
|
|||
XPG wrote:
Disable the STPI interface. It's too new in Burnatonce. Use ASPI 4.60 to access drives. Thank you, I tried this, disabling the STPI-Interface and installing ASPI (version 4.71, since I didn't find 4.60 for WinXP anywhere...), but it still says: ASPILOCK:1,1,0: CD-RW CDR-5W48 Rev: VSG3 Starting write at speed 48... Turning BURN-Proof on Executing power calibration... ?: I/O error. : scsi sendcmd: retryable error CDB: 54 01 00 00 00 00 00 00 00 00 status: 0x0 (GOOD STATUS) cmd finished after 5.458s timeout 180s ERROR: Power calibration failed. ERROR: Use option --force to ignore this error. ERROR: Writing failed. Any other idea? Best regards Lars |
#4
|
|||
|
|||
Lars Janssen wrote:
XPG wrote: Disable the STPI interface. It's too new in Burnatonce. Use ASPI 4.60 to access drives. Thank you, I tried this, disabling the STPI-Interface and installing ASPI (version 4.71, since I didn't find 4.60 for WinXP anywhere...), Links to ForceASPI (which installs 4.60) are he http://aspi.radified.com/ but it still says: ASPILOCK:1,1,0: CD-RW CDR-5W48 Rev: VSG3 Starting write at speed 48... Turning BURN-Proof on Executing power calibration... ?: I/O error. : scsi sendcmd: retryable error CDB: 54 01 00 00 00 00 00 00 00 00 status: 0x0 (GOOD STATUS) cmd finished after 5.458s timeout 180s ERROR: Power calibration failed. ERROR: Use option --force to ignore this error. ERROR: Writing failed. Any other idea? Best regards Lars |
#5
|
|||
|
|||
Thank you, I tried this, disabling the STPI-Interface and installing ASPI (version 4.71, since I didn't find 4.60 for WinXP anywhere...), but it still says: Burnatonce doesn't work with ASPI 4.7x: http://www.burnatonce.com/forums/ind...act=ST&f=4&t=3 I haven't heard any problem with ASPI 4.60 in WinXP (I have it installed in fact). http://www.burnatonce.com/forums/index.php |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Power supply can zap motherboard? | Eric Popelka | Homebuilt PC's | 8 | June 18th 05 08:54 PM |
power supply, or ...? | ynotssor | General | 10 | June 1st 04 01:19 AM |
No Power to Motherboard | Matt | Homebuilt PC's | 4 | January 5th 04 09:17 PM |
Happy Birthday America | SST | Overclocking | 333 | November 27th 03 07:54 PM |
Happy Birthday America | SST | Overclocking AMD Processors | 326 | November 27th 03 07:54 PM |