If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Question about old HDD
Hello!
I have a strange question about an old hard drive that I pulled out of an old Pentium 1 computer. The hard drive was working fine, and the computer was able to boot into Windows 95 fine. Then I decided to run SpinRite6 to check if the hdd had any bad sectors. SpinRite6 booted fine from a diskette and detected the drive. Then it refused to do any kind of work from the drive and claimed that the partition size was larger than the drive size indicated in the computer bios. The drive is a Western Digital caviar and its label indicates that it has 2484 cyl; 16 heads; 63 sect; 1281.9 MB. http://e.271828.p.31415.googlepages.com/s_IMG_2558.jpg The computer auto-detected the drive as following: 2484; 16; 63; 1223 MB. This configuration was able to read the drive fine, but SpinRite gives this: http://e.271828.p.31415.googlepages.com/s_IMG_2558.jpg http://e.271828.p.31415.googlepages.com/s_IMG_2561.jpg Then I pulled the drive and stuck it in a newer Pentium 4 computer and it detected it as follows: cyl :620; hds: 64; sectors: 63. Total sectors 2502872 Spinrite ran fine. When I stuck the drive back into the old computer I tried this configuration and got 1221 MB. http://e.271828.p.31415.googlepages.com/s_IMG_2560.jpg The computer also booted up quite fine and made it into windows. Spinrite still did not want to run on it and claims that only 619 cyl are specified. http://e.271828.p.31415.googlepages.com/s_IMG_2562.jpg What is going on? I have extensive experience with modern hardware, but this is my first experience with such old hardware. Can somebody please explain or clarify what is going on: How can the harddrive be detected fine with 2 different configurations, which one is the correct one, and why does Spin Rite read the drive on the newer computer but refuses to read it on the old computer with either of the 2 configurations. Thank you! |
#3
|
|||
|
|||
Question about old HDD
"Arno Wagner" wrote in message
Previously wrote: Hello! I have a strange question about an old hard drive that I pulled out of an old Pentium 1 computer. The hard drive was working fine, and the computer was able to boot into Windows 95 fine. Then I decided to run SpinRite6 to check if the hdd had any bad sectors. SpinRite6 booted fine from a diskette and detected the drive. Then it refused to do any kind of work from the drive and claimed that the partition size was larger than the drive size indicated in the computer bios. SpoinRite is old and completely irrelevant for ATA disks. Do not use it. Ignore the idiot babblebot. The drive is a Western Digital caviar and its label indicates that it has 2484 cyl; 16 heads; 63 sect; 1281.9 MB. http://e.271828.p.31415.googlepages.com/s_IMG_2558.jpg The computer auto-detected the drive as following: 2484; 16; 63; 1223 MB. That is the default translation as found in the drive's identification sector. This configuration was able to read the drive fine, but SpinRite gives this: http://e.271828.p.31415.googlepages.com/s_IMG_2561.jpg Then I pulled the drive and stuck it in a newer Pentium 4 computer and it detected it as follows: cyl :620; hds: 64; sectors: 63. Total sectors 2502872 So now the question becomes: what CHS is used in the drive's MBR. If that's the same as above than the bios isn't doing any translation and forces the 620 : 64 : 63 CHS translation on the drive. Spinrite ran fine. When I stuck the drive back into the old computer I tried this configuration and got 1221 MB. http://e.271828.p.31415.googlepages.com/s_IMG_2560.jpg The computer also booted up quite fine and made it into windows. Spinrite still did not want to run on it and claims that only 619 cyl are specified. http://e.271828.p.31415.googlepages.com/s_IMG_2562.jpg What is going on? I have extensive experience with modern hardware, but this is my first experience with such old hardware. Can somebody please explain or clarify what is going on: How can the harddrive be detected fine with 2 different configurations, which one is the correct one, and why does Spin Rite read the drive on the newer computer but refuses to read it on the old computer with either of the 2 configurations. Drive geometry is done by the BOS for ATA drives. Nonsense. It does it for any drive. It has no relation to the real disk geometry. Different BIOSes may use different CS translation. Because you either tell it what to use or it makes a calculated guess according to what it finds on the drive (default translation or MBR). The way to deal with this is to use LBA mode. Which is what the P4 does. CHS is not used so setting doesn't matter. Apparently the P1 doesn't have Int13 extensions and has to deal with CHS and the correct setting obviously matters there. I'm betting that the drive was partitioned with the cyl 620; hds: 64; sectors: 63 setting. Apparently that is bigger than the drive is, according to the P1 BIOS. Sounds like the P1 bios may be limited. You could try modifying the cyl value in MBR and see if that satisfies SpinRite. That SpinRite does not deal with it is a limitation of SpinRite. I advise to stop using it. Ignore the babblebot moron. Arno |
#4
|
|||
|
|||
Question about old HDD
I am still not clear on how the hdd cam work with the 2 different
configurations. They give different numbers of total sectors... |
#5
|
|||
|
|||
Question about old HDD
wrote in message ups.com
I am still not clear Maybe you should read again what you foolishly snipped. on how the hdd cam work with the 2 different configurations. What exactly did you not understand in using LBA instead of CHS. They give different numbers of total sectors... What exactly did you not understand in the word "limited" and what the consequence of such a "limitation" might be. |
#6
|
|||
|
|||
Question about old HDD
|
#7
|
|||
|
|||
Question about old HDD
"Arno Wagner" wrote in message
Previously wrote: I am still not clear on how the hdd cam work with the 2 different configurations. They give different numbers of total sectors... The configuration is not in the HDD. Yes it is, clueless Babblebot. It is a "fiction" the BIOS makes up from what the HDD tells it. See, it is. The readon is that HDDs can have much more cylinders/heads.sectors Cylinders, babblebot, cylinders. than old BIOSes could handle. The rea's'on is that HDs use different limits for C, H and S than bioses do, P(CHS) and L(CHS). That's why they are called a translating bios. Drives still have an unchanged 16-heads limit whereas the new bios was enhanced by setting the heads limit at 256. Drives have an enhanced cylinder limit (65536) whereas the new bios still has the old 1024 cylinder limit of the legacy bios. The total limit for both of them is the same CxHxSx512 = ~8GB Ubnfortunately, before LBA there was no standard way Yes there was, problem was there were two standard ways: LBA(assist) and Large (or bitshift). A good bios should be able to tell from the MBR CHS -by checking against the rules for each- which one was used. to do this translation. Maybe because there is no translation in using LBA? Moron babblebot. But even an Int13 extended (LBA) BIOS can use CHS for addressing a drive and use a CHS of it's choice. Arno |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Perhaps and off topic question....but could use some help with video question.....I don't need codec help, just a general question. | Bret Miller | Homebuilt PC's | 0 | October 13th 06 12:23 AM |
[Question] Asus A8N-SLI Single Video card application question | PB | Asus Motherboards | 3 | April 7th 06 08:54 AM |
Good morning or good evening depending upon your location. I want to ask you the most important question of your life. Your joy or sorrow for all eternity depends upon your answer. The question is: Are you saved? It is not a question of how good | Remnant Banana | General | 5 | April 23rd 05 02:40 AM |
Good morning or good evening depending upon your location. I want to ask you the most important question of your life. Your joy or sorrow for all eternity depends upon your answer. The question is: Are you saved? It is not a question of how good | RFM | Printers | 0 | April 23rd 05 01:23 AM |
Good morning or good evening depending upon your location. I want to ask you the most important question of your life. Your joy or sorrow for all eternity depends upon your answer. The question is: Are you saved? It is not a question of how good | Yddap | Dell Computers | 0 | April 22nd 05 01:00 AM |