If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
How do I configure RAID on a FC5300? Is there a console?
Hello All. I just purchased an EMC Clariion FC5300 (also known as
Dell 650F). I've got an 005-044993 RAID storage processor--w/ lots of cache. I've got Cable/HyperTerm plugged into RJ12.. 9600/8/1/even, hardware flow control----but nothing comes up. I can see a cursor pause when I press a key in hyperterminal, but that's it?! Can anyone tell me what I need to do the get the console to come up so I can configure the RAID features of the SP? If I'm missing the boat and the RJ12 isn't for configuring the device--please tell me what the real answer is, and feel free to call me 'thick'. Thanks in advance for any/all comments. Leo. |
#2
|
|||
|
|||
Bring in EMC and pay them for it.
Or I can come in and do it for much cheaper. :-) "Leo Unacalx" wrote in message ... Hello All. I just purchased an EMC Clariion FC5300 (also known as Dell 650F). I've got an 005-044993 RAID storage processor--w/ lots of cache. I've got Cable/HyperTerm plugged into RJ12.. 9600/8/1/even, hardware flow control----but nothing comes up. I can see a cursor pause when I press a key in hyperterminal, but that's it?! Can anyone tell me what I need to do the get the console to come up so I can configure the RAID features of the SP? If I'm missing the boat and the RJ12 isn't for configuring the device--please tell me what the real answer is, and feel free to call me 'thick'. Thanks in advance for any/all comments. Leo. |
#3
|
|||
|
|||
"Leo Unacalx" wrote in message ... Hello All. I just purchased an EMC Clariion FC5300 (also known as Dell 650F). I've got an 005-044993 RAID storage processor--w/ lots of cache. I've got Cable/HyperTerm plugged into RJ12.. 9600/8/1/even, hardware flow control----but nothing comes up. I can see a cursor pause when I press a key in hyperterminal, but that's it?! Can anyone tell me what I need to do the get the console to come up so I can configure the RAID features of the SP? If I'm missing the boat and the RJ12 isn't for configuring the device--please tell me what the real answer is, and feel free to call me 'thick'. Thanks in advance for any/all comments. Leo. Read this NG infrequently - the following might help: http://support.dell.com/support/topi...l=en&s=gen&cs= |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
IDE RAID | Ted Dawson | Asus Motherboards | 29 | September 21st 04 03:39 AM |
Need help with SATA RAID 1 failure on A7N8X Delux | Cameron | Asus Motherboards | 10 | September 6th 04 11:50 PM |
Asus P4C800 Deluxe ATA SATA and RAID Promise FastTrack 378 Drivers and more. | Julian | Asus Motherboards | 2 | August 11th 04 12:43 PM |
Gigabyte GA-8KNXP and Promise SX4000 RAID Controller | Old Dude | Gigabyte Motherboards | 4 | November 12th 03 07:26 PM |
RAID-1 reliability | marcodeo | Storage (alternative) | 26 | August 30th 03 09:53 PM |