If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
I solved a problem today that I have had since I have been building computers.
No more trial and error in screw sizes.
I bought one of each of these (nuts): 6-32 x .25": Used in PC case cover and I/O plates 6-32 x .15": Used to install hard drives M3 x .25": Used to install floppy drive, CD-ROM drive and motherboard 4-40 x .18": Used in I/O plate connector And one of these: http://www.toolup.com/empire-level_2...FZDm7AodYkAAhg |
#2
|
|||
|
|||
I solved a problem today that I have had since I have been buildingcomputers.
Metspitzer wrote:
No more trial and error in screw sizes. I bought one of each of these (nuts): 6-32 x .25": Used in PC case cover and I/O plates 6-32 x .15": Used to install hard drives M3 x .25": Used to install floppy drive, CD-ROM drive and motherboard 4-40 x .18": Used in I/O plate connector And one of these: http://www.toolup.com/empire-level_2...FZDm7AodYkAAhg I use those magnets here. At one time, The Source (our equivalent of Radio Shack) used to carry them. But I've also found them at the hardware store. The price is highly variable, with some stores trying to gouge you for those magnets. The ceramic magnets will "chip" on the edge, if struck or dropped. Otherwise, I like them. I have around 20 to 25 of those magnets, and they're all busy "doing stuff" :-) If you build your own computers, and purchase a computer case in a cardboard box as part of your build, those come with a bag of screws. And if I needed a fastener of the sort you list, I'd go through the left-overs from those bags, to see if I had any. At one time, a "retail" hard drive purchase, came in a cardboard box, with a foam liner. And include 3.5" to 5.25" U-shaped pieces for drive mounting conversion, as well as eight screws to fit that stuff. And that's where some of my drive screws came from. Even if the Maxtor drives that came in those boxes died, the screws lived on to help the replacement drives. Paul |
#3
|
|||
|
|||
I solved a problem today that I have had since I have been building computers.
On Sun, 26 Jan 2014 17:45:20 -0500, Paul wrote:
And if I needed a fastener of the sort you list, I'd go through the left-overs from those bags, to see if I had any. Mine's so large I've 6x6x6" box to hold them (several bags;- I subcategorizes them ) |
#4
|
|||
|
|||
I solved a problem today that I have had since I have been building computers.
On Sun, 26 Jan 2014 19:26:21 -0500, Flasherly
wrote: On Sun, 26 Jan 2014 17:45:20 -0500, Paul wrote: And if I needed a fastener of the sort you list, I'd go through the left-overs from those bags, to see if I had any. Mine's so large I've 6x6x6" box to hold them (several bags;- I subcategorizes them ) Go to the hardware and get one of those many-compartment boxes. Ideal for organizing your screws. |
#5
|
|||
|
|||
I solved a problem today that I have had since I have been building computers.
On Wed, 29 Jan 2014 07:29:42 -0800, Loren Pechtel
wrote: Go to the hardware and get one of those many-compartment boxes. Ideal for organizing your screws. You should see the garage. Finding deals for awhile turned into collecting tools. (Lot of metal oriented, table drills, welders, grinders, air tools, and various stuff. Not a wood guy.) Seems I'd buy more tools just to keep the existing tools organized. And I'll stop a job, totally weirds me out, if I don't knowing -exactly- where everything I've pulled out for the job setup is located. (Oh, well, buy and use a tool once from China/Harbor Freight, and it'll usually pay for itself many times over.) O - the organizing boxes. Yea, I've got them, couple of big ones, except they're only storing tear-downs on scavenges on whatever's worth keeping. Computers I can build in my sleep. |
#6
|
|||
|
|||
I solved a problem today that I have had since I have been buildingcomputers.
On 01/26/2014 01:56 PM, Metspitzer wrote:
No more trial and error in screw sizes. I bought one of each of these (nuts): 6-32 x .25": Used in PC case cover and I/O plates 6-32 x .15": Used to install hard drives M3 x .25": Used to install floppy drive, CD-ROM drive and motherboard 4-40 x .18": Used in I/O plate connector And one of these: http://www.toolup.com/empire-level_2...ets-2-pcs.aspx If you ever see a microwave oven on the side of the road waiting for the trashman, you can harvest two nice ceramic donut magnets from the magnetron inside. You do need to be careful around the deadly capacitor inside there, as it is of the order of 1uF at 2kV, so discharge it once you get inside. I've got about sixty or so of them; put them in series and they've got a pretty good tug. Jon |
#7
|
|||
|
|||
I solved a problem today that I have had since I have been buildingcomputers.
Jon Danniken wrote:
On 01/26/2014 01:56 PM, Metspitzer wrote: No more trial and error in screw sizes. I bought one of each of these (nuts): 6-32 x .25": Used in PC case cover and I/O plates 6-32 x .15": Used to install hard drives M3 x .25": Used to install floppy drive, CD-ROM drive and motherboard 4-40 x .18": Used in I/O plate connector And one of these: http://www.toolup.com/empire-level_2...ets-2-pcs.aspx If you ever see a microwave oven on the side of the road waiting for the trashman, you can harvest two nice ceramic donut magnets from the magnetron inside. You do need to be careful around the deadly capacitor inside there, as it is of the order of 1uF at 2kV, so discharge it once you get inside. I've got about sixty or so of them; put them in series and they've got a pretty good tug. Jon Jon will be giving a safety course later, on how not to die while playing inside your microwave oven :-) Paul |
#8
|
|||
|
|||
I solved a problem today that I have had since I have been buildingcomputers.
On 01/27/2014 02:57 AM, Paul wrote:
Jon Danniken wrote: On 01/26/2014 01:56 PM, Metspitzer wrote: No more trial and error in screw sizes. I bought one of each of these (nuts): 6-32 x .25": Used in PC case cover and I/O plates 6-32 x .15": Used to install hard drives M3 x .25": Used to install floppy drive, CD-ROM drive and motherboard 4-40 x .18": Used in I/O plate connector And one of these: http://www.toolup.com/empire-level_2...ets-2-pcs.aspx If you ever see a microwave oven on the side of the road waiting for the trashman, you can harvest two nice ceramic donut magnets from the magnetron inside. You do need to be careful around the deadly capacitor inside there, as it is of the order of 1uF at 2kV, so discharge it once you get inside. I've got about sixty or so of them; put them in series and they've got a pretty good tug. Jon Jon will be giving a safety course later, on how not to die while playing inside your microwave oven :-) Indeed I will! I saw a video on YT recently where a fellow hooked up a mangetron (and associated components) outside of a microwave, and turned it on. I don't think I've cringed that hard in my life. Jon |
#9
|
|||
|
|||
I solved a problem today that I have had since I have been building computers.
"Jon Danniken" wrote in message ... On 01/27/2014 02:57 AM, Paul wrote: Jon Danniken wrote: On 01/26/2014 01:56 PM, Metspitzer wrote: No more trial and error in screw sizes. I bought one of each of these (nuts): 6-32 x .25": Used in PC case cover and I/O plates 6-32 x .15": Used to install hard drives M3 x .25": Used to install floppy drive, CD-ROM drive and motherboard 4-40 x .18": Used in I/O plate connector And one of these: http://www.toolup.com/empire-level_2...ets-2-pcs.aspx If you ever see a microwave oven on the side of the road waiting for the trashman, you can harvest two nice ceramic donut magnets from the magnetron inside. You do need to be careful around the deadly capacitor inside there, as it is of the order of 1uF at 2kV, so discharge it once you get inside. I've got about sixty or so of them; put them in series and they've got a pretty good tug. Jon Jon will be giving a safety course later, on how not to die while playing inside your microwave oven :-) Indeed I will! I saw a video on YT recently where a fellow hooked up a mangetron (and associated components) outside of a microwave, and turned it on. I don't think I've cringed that hard in my life. Jon Social Darwinism.... Chris |
#10
|
|||
|
|||
I solved a problem today that I have had since I have been buildingcomputers.
On 26/01/2014 4:56 PM, Metspitzer wrote:
No more trial and error in screw sizes. I bought one of each of these (nuts): 6-32 x .25": Used in PC case cover and I/O plates 6-32 x .15": Used to install hard drives M3 x .25": Used to install floppy drive, CD-ROM drive and motherboard 4-40 x .18": Used in I/O plate connector And one of these: http://www.toolup.com/empire-level_2...FZDm7AodYkAAhg What is the magnet for? To magnetize a screwdriver, so it can pick up nuts that fall? You can use any standard fridge magnet for that. Yousuf Khan |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Problem already solved but Iwant to learn what caused the problem. TIA | Rod Speed | General | 7 | October 16th 06 03:14 AM |
New to building computers, and just have some general questions | brboyle | General | 2 | November 27th 05 08:50 AM |
OpenGL failed to initialize -- Problem Solved!!! well kind of solved. | Jose Jiminez | Nvidia Videocards | 5 | January 13th 04 11:51 AM |
building stable computers for Mom/Grandma....HELP!! | rferoni | Homebuilt PC's | 11 | December 10th 03 02:08 AM |
Lexmark problem solved - new problem! forgot Password ?! | Pret Orian | Printers | 0 | September 26th 03 05:01 PM |