If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Is my hard drive the source of my CD burning woes?
This problem has been vexing me for nearly two months now. Here's the
background; I'll try to be brief: After years of trouble-free CD burning, I've been struggling with a real problem ... burns proceed normally until read-out, then fail. The many, many error reports I've collected (using several different pieces of burning software) all end more or less like this: 5:00:44 PM #21 SCSI -1066 File Cdrdrv.cpp, Line 1431 SCSI Exec, HA 1, TA 1, LUN 0, buffer 0x07770000 Status: 0x04 (0x01, SCSI_ERR) HA-Status 0x00 (0x00, OK) TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND) [snip] 5:00:45 PM #22 CDR -1066 File Writer.cpp, Line 301 Invalid field in command 5:00:45 PM #23 Text 0 File ThreadedTransfer.cpp, Line 229 all writers idle, stopping conversion 5:00:46 PM #24 Text 0 File dlgbrnst.cpp, Line 1658 Set remaining time: 0:00,000 (0ms) - OK 5:00:46 PM #25 Phase 38 File dlgbrnst.cpp, Line 1800 Burn process failed at 12x (1,800 KB/s) I've done all of the following, without fixing the problem: (1) Clean install of Win2000 (2) Uninstall, reinstall all manner of burning software packages: Adaptec, Roxio, Nero, Feurio (3) Replaced old Plextor drive (and legacy CD-ROM drive) with new Plextor DVD/CDR drive and separate Liteon CDR drive. Former uses Roxio, latter Nero as burning software. .. Interestingly, as was true with my old drives and continues to be true with the new onesupon reboot I usually get two or three full burns, then the failures begin again. I'm pretty convinced by now that this isn't a software problem; one error message I got using the Roxio program suggests that the drive is "stopping" during burning. (Though there's no apparent impact on the visible buffer reading, i.e., it doesn't drop to zero from 87% or wherever it spends its free time during burning.) This made me think that my four-year-old hard drive (C may in fact be the problem, though it hasn't given me any other trouble. I recently installed a second hard drive, which is labeled D: by Win200. I tried copying the Roxio program folder over to my new D: drive, along with some data files to burn, thinking that might solve the problem ... but it didn't. I then tried to "reinstall" both the Roxio and Nero programs to the D: drive (after uninstalling them from the C: drive), but neither would let me do that: they both installed to C: without offering any other option. So here, at last, is my question. Really three questions: (1) Does the error report above, or the anecdotal evidence I've provided, confirm the notion that my old hard drive is the culprit? (2) If so, what do I have to do to install one or both CD-burning software packages to the D: drive? Is this a master/slave kinda deal? Are there little switches and widgets and connections inside the box that I, as a hamfisted English major, won't know how to deal with? And if I change the parameters of both drives, will all the programs currently on my C: drive (and functioning well) have to migrate there too? (3) Or should I just bite the bullet, back up as much data to CDR as possible from C:, and replace that drive too? I'm really at my wits' end ... so to those who persevered through all this verbiage, TIA! jonking |
#2
|
|||
|
|||
"Jonathan King" wrote in message
... This problem has been vexing me for nearly two months now. Here's the background; I'll try to be brief: After years of trouble-free CD burning, I've been struggling with a real problem ... burns proceed normally until read-out, then fail. The many, many error reports I've collected (using several different pieces of burning software) all end more or less like this: snip CD burners don't last forever. 3 to 5 years is the norm but some 2 years ago there was a shortage of laser diodes and I think lower quality units were used as a result. My company's returns shelves contain many mainly HP and Acer burners that lasted between 14 and 20 months. |
#4
|
|||
|
|||
If you install BOTH Roxio and Nero on a computer you will get a software
conflict. Remove one of them. -- DaveW "Jonathan King" wrote in message ... This problem has been vexing me for nearly two months now. Here's the background; I'll try to be brief: After years of trouble-free CD burning, I've been struggling with a real problem ... burns proceed normally until read-out, then fail. The many, many error reports I've collected (using several different pieces of burning software) all end more or less like this: 5:00:44 PM #21 SCSI -1066 File Cdrdrv.cpp, Line 1431 SCSI Exec, HA 1, TA 1, LUN 0, buffer 0x07770000 Status: 0x04 (0x01, SCSI_ERR) HA-Status 0x00 (0x00, OK) TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND) [snip] 5:00:45 PM #22 CDR -1066 File Writer.cpp, Line 301 Invalid field in command 5:00:45 PM #23 Text 0 File ThreadedTransfer.cpp, Line 229 all writers idle, stopping conversion 5:00:46 PM #24 Text 0 File dlgbrnst.cpp, Line 1658 Set remaining time: 0:00,000 (0ms) - OK 5:00:46 PM #25 Phase 38 File dlgbrnst.cpp, Line 1800 Burn process failed at 12x (1,800 KB/s) I've done all of the following, without fixing the problem: (1) Clean install of Win2000 (2) Uninstall, reinstall all manner of burning software packages: Adaptec, Roxio, Nero, Feurio (3) Replaced old Plextor drive (and legacy CD-ROM drive) with new Plextor DVD/CDR drive and separate Liteon CDR drive. Former uses Roxio, latter Nero as burning software. . Interestingly, as was true with my old drives and continues to be true with the new onesupon reboot I usually get two or three full burns, then the failures begin again. I'm pretty convinced by now that this isn't a software problem; one error message I got using the Roxio program suggests that the drive is "stopping" during burning. (Though there's no apparent impact on the visible buffer reading, i.e., it doesn't drop to zero from 87% or wherever it spends its free time during burning.) This made me think that my four-year-old hard drive (C may in fact be the problem, though it hasn't given me any other trouble. I recently installed a second hard drive, which is labeled D: by Win200. I tried copying the Roxio program folder over to my new D: drive, along with some data files to burn, thinking that might solve the problem ... but it didn't. I then tried to "reinstall" both the Roxio and Nero programs to the D: drive (after uninstalling them from the C: drive), but neither would let me do that: they both installed to C: without offering any other option. So here, at last, is my question. Really three questions: (1) Does the error report above, or the anecdotal evidence I've provided, confirm the notion that my old hard drive is the culprit? (2) If so, what do I have to do to install one or both CD-burning software packages to the D: drive? Is this a master/slave kinda deal? Are there little switches and widgets and connections inside the box that I, as a hamfisted English major, won't know how to deal with? And if I change the parameters of both drives, will all the programs currently on my C: drive (and functioning well) have to migrate there too? (3) Or should I just bite the bullet, back up as much data to CDR as possible from C:, and replace that drive too? I'm really at my wits' end ... so to those who persevered through all this verbiage, TIA! jonking |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
two hd's on same IDE channel | Steve James | General | 25 | March 13th 04 12:06 AM |
Mysterious Hard Drive Problem | Bill Anderson | General | 4 | January 18th 04 03:43 AM |
Multi-boot Windows XP without special software | Timothy Daniels | General | 11 | December 12th 03 05:38 AM |
Help! WinXP can't tell that my 2nd hard drive is already formatted | FitPhillyGuy | General | 12 | September 26th 03 03:38 AM |
Seagate Hard Drive - Faulty? | Mike Walker | General | 2 | September 5th 03 02:06 AM |