|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
November 5th 03, 09:48 AM
|
|||
|
|||
warning!! cpu clock or ratio are programming fail
"warning!! cpu clock or ratio are programming fail previously Please
setup CPU clock again" what does this mean? the machine in question E-8K5A2 / 2000XP cpu stock standard.... after a hardware device is installed eg: mitsubishi pro internet keyboard / magic software hp usb printer, mitsu 1770h monitor the above error comes up after restart and then is ok after 2nd reboot.... speeds are correct everytime in intial post screen 1633mhz and multiplier 12.5x133 bios reads 133 mhz and auto...12.5 x not available so set on auto any tips ideas etc please and thank you this drive me nuttles :-/ ray 
|
|
#2
November 5th 03, 11:05 AM
|
|||
|
|||
|
hi
just means that cpu init. failed! no wory unless it's becommung frequent. can be a indicator of bad/to small psu. coco "Ray" skrev i meddelandet news:3dc8e2c2.11717038@news-server... "warning!! cpu clock or ratio are programming fail previously Please setup CPU clock again" what does this mean? the machine in question E-8K5A2 / 2000XP cpu stock standard.... after a hardware device is installed eg: mitsubishi pro internet keyboard / magic software hp usb printer, mitsu 1770h monitor the above error comes up after restart and then is ok after 2nd reboot.... speeds are correct everytime in intial post screen 1633mhz and multiplier 12.5x133 bios reads 133 mhz and auto...12.5 x not available so set on auto any tips ideas etc please and thank you this drive me nuttles :-/ ray
|
|
#3
November 5th 03, 11:05 AM
|
|||
|
|||
|
hi
just means that cpu init. failed! no wory unless it's becommung frequent. can be a indicator of bad/to small psu. coco "Ray" skrev i meddelandet news:3dc8e2c2.11717038@news-server... "warning!! cpu clock or ratio are programming fail previously Please setup CPU clock again" what does this mean? the machine in question E-8K5A2 / 2000XP cpu stock standard.... after a hardware device is installed eg: mitsubishi pro internet keyboard / magic software hp usb printer, mitsu 1770h monitor the above error comes up after restart and then is ok after 2nd reboot.... speeds are correct everytime in intial post screen 1633mhz and multiplier 12.5x133 bios reads 133 mhz and auto...12.5 x not available so set on auto any tips ideas etc please and thank you this drive me nuttles :-/ ray
|
|
#4
November 5th 03, 04:18 PM
|
|||
|
|||
|
I had that problem too, could it be when you switch power supplies , it does
it the first time too? went to an antec sl350 "CoCo" wrote in message ... hi just means that cpu init. failed! no wory unless it's becommung frequent. can be a indicator of bad/to small psu. coco "Ray" skrev i meddelandet news:3dc8e2c2.11717038@news-server... "warning!! cpu clock or ratio are programming fail previously Please setup CPU clock again" what does this mean? the machine in question E-8K5A2 / 2000XP cpu stock standard.... after a hardware device is installed eg: mitsubishi pro internet keyboard / magic software hp usb printer, mitsu 1770h monitor the above error comes up after restart and then is ok after 2nd reboot.... speeds are correct everytime in intial post screen 1633mhz and multiplier 12.5x133 bios reads 133 mhz and auto...12.5 x not available so set on auto any tips ideas etc please and thank you this drive me nuttles :-/ ray
|
|
#5
November 5th 03, 04:18 PM
|
|||
|
|||
|
I had that problem too, could it be when you switch power supplies , it does
it the first time too? went to an antec sl350 "CoCo" wrote in message ... hi just means that cpu init. failed! no wory unless it's becommung frequent. can be a indicator of bad/to small psu. coco "Ray" skrev i meddelandet news:3dc8e2c2.11717038@news-server... "warning!! cpu clock or ratio are programming fail previously Please setup CPU clock again" what does this mean? the machine in question E-8K5A2 / 2000XP cpu stock standard.... after a hardware device is installed eg: mitsubishi pro internet keyboard / magic software hp usb printer, mitsu 1770h monitor the above error comes up after restart and then is ok after 2nd reboot.... speeds are correct everytime in intial post screen 1633mhz and multiplier 12.5x133 bios reads 133 mhz and auto...12.5 x not available so set on auto any tips ideas etc please and thank you this drive me nuttles :-/ ray
|
|
#6
November 6th 03, 06:36 PM
|
|||
|
|||
|
Reset your bios to default and see if you have the problem. If you still
have the problem try reseating all connectors and cards and even reseat the motherboard battery. Then try stepping up and overclock a little at the time. regards B "Ray" wrote in message news:3dc8e2c2.11717038@news-server... "warning!! cpu clock or ratio are programming fail previously Please setup CPU clock again" what does this mean? the machine in question E-8K5A2 / 2000XP cpu stock standard.... after a hardware device is installed eg: mitsubishi pro internet keyboard / magic software hp usb printer, mitsu 1770h monitor the above error comes up after restart and then is ok after 2nd reboot.... speeds are correct everytime in intial post screen 1633mhz and multiplier 12.5x133 bios reads 133 mhz and auto...12.5 x not available so set on auto any tips ideas etc please and thank you this drive me nuttles :-/ ray
|
|
#7
November 6th 03, 06:36 PM
|
|||
|
|||
|
Reset your bios to default and see if you have the problem. If you still
have the problem try reseating all connectors and cards and even reseat the motherboard battery. Then try stepping up and overclock a little at the time. regards B "Ray" wrote in message news:3dc8e2c2.11717038@news-server... "warning!! cpu clock or ratio are programming fail previously Please setup CPU clock again" what does this mean? the machine in question E-8K5A2 / 2000XP cpu stock standard.... after a hardware device is installed eg: mitsubishi pro internet keyboard / magic software hp usb printer, mitsu 1770h monitor the above error comes up after restart and then is ok after 2nd reboot.... speeds are correct everytime in intial post screen 1633mhz and multiplier 12.5x133 bios reads 133 mhz and auto...12.5 x not available so set on auto any tips ideas etc please and thank you this drive me nuttles :-/ ray
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| ECS Pathetic Technical Support | Pedro Corbett | General | 14 | July 29th 04 03:53 AM |
Linear Mode
