In article , "Pete"
wrote:

Pete wrote:
Paul wrote:
In article , "Pete"
wrote:

I have just bought a Ultra Xconnect power supply 400watts to use in
conjunction with a AMD 3500+ and skt 939 board.

Here it is:


http://www.ultraproducts.com/product...roductID=3 04

It says it supports Pentium 4 and AMD CPUs and meets ATX version
2.03 and ATX 12V version 1.2 specification.

When I bought it I thought it was the dogs ******** but now I see
motherboards with 24 pin PSU connectors and wonder what's going on.


Have I bought a lemon? Is it out of date? Has the ATX spec moved on?

Can you plug a 20pin ATX connector from the power supply onto a
24pin connector on the motherboard and then use a 4 pin lead for the
remaining 4 pins or would I need a convertor?


The motherboard I want to use it with has the following connectors:

24-pin ATX Power connector
4-pin ATX 12V Power connector

Would I need to buy extra cables / convertors to use it with this
board?

Thanks

Pete

----- ATX 2.0+ main connector ----- --- ATX previous versions
---

Pin Signal Color Pin Signal Color Pin Signal Color Pin
Signal Color 1 +3.3VDC Orange 13 +3.3VDC Orange 1 +3.3VDC Orange
11 +3.3VDC Orange 2 +3.3VDC Orange 14 -12VDC Blue 2 +3.3VDC
Orange 12 -12VDC Blue 3 COM Black 15 COM Black 3 COM
Black 13 COM Black 4 +5VDC Red 16 PS_ON# Green 4
+5VDC Red 14 PS_ON# Green 5 COM Black 17 COM Black
5 COM Black 15 COM Black 6 +5VDC Red 18 COM Black
6 +5VDC Red 16 COM Black 7 COM Black 19 COM Black
7 COM Black 17 COM Black 8 PWR_OK Gray 20 Reserved N/C
8 PWR_OK Gray 18 Reserved
N/C (-5V)
9 +5VSB Purple 21 +5VDC Red 9 +5VSB Purple 19 +5VDC
Red 10 +12V1DC Yellow 22 +5VDC Red 10 +12VDC Yellow 20
+5VDC Red 11 +12V1DC Yellow 23 +5VDC Red
12 +3.3 VDC Orange 24 COM Black

--- ATX 2.0+ 12V for proc ------ --- ATX previous versions
---
Pin Signal Color Pin Signal Color Pin Signal Color Pin
Signal Color 1 COM Black 3 +12V2DC Yellow/Black 1 COM Black
3 +12VDC Yellow 2 COM Black 4 +12V2DC Yellow/Black 2 COM Black
4 +12VDC Yellow

Changes:

1) -5V removed, prev supplies probably had it. Usually not an issue.
2) Four addition pins on main connector. Extra +3.3V, +5V, +12V, GND
Helps with PCI Express motherboards. For SLI boards, 24 pin
recommended (to get two 6 amp pins to feed the two video cards via
PCI Express slot connectors). For single video card, 20 pin is
generally enough. 6600GT for example, draws 4 amps. Xbitlabs.com
has measured many cards. If in doubt, do a detailed calculation.
3) 12V output split into two separate 12V circuits.
No advantage to customer, due to need to allocate extra "slack"
when buying. Perhaps intended to meet IEC60950 ? (To limit max
power per 12V output) 12V1 feeds disks and motherboard (and video
card) 12V2 used exclusively for processor (in your computer, that
would be 8.24A)

* 24 pin can plug to 20 pin mobo, as long as pins don't bump
20 pin can plug to 24 pin mobo (same pinout) - use the right holes.
Some 24 pin are detachable, into a 20 pin part and a detached 4 pin
part. At least one guy has managed to plug the detached 4 pin, into
the processor Vcore input. (I haven't checked to see how hard that
is to do.)

PCI Express slots have 12V pins on them and allow up to 5 amps.
Video cards (not overclocked) seem to be designed to draw about 4
amps or a tiny bit more, through the PCI Express x16 slot. The
single 12V wire on the 20 pin connector carries at least 6 amps, so
using a 20 pin connector on a non-SLI board seems reasonable. The
fan header current also flows through the single 12V pin on the 20
pin connector. Main connector rated for 6 amps per pin.

http://www.molex.com/cgi-bin/bv/mole...roductID=98716

12V processor power connect pins rated at 8 amps per pin.

http://www.molex.com/cgi-bin/bv/mole...roductID=76873

Molex disk drive connector rated at 8 amps per pin (based on assuming
a right angle PCB mount connector, and 18 gauge wire - Amp 82181
catalog)

Enjoy your new power supply. No need for adapters.

The Ultra you have selected, has 12V @ 16A. If you had an 89W AMD
processor, that is (89W/12V)/0.90 = 8.24A. A midrange video card like
6600GT is 4A. That is 12.24 amps so far. A disk drive idles at 0.5A.
A CDROM can draw 1.5A according to the rating on the label. Allocate
0.5A for some fans. We are now at 14.74 amps of 16A. Your new Ultra
is suitable for a midrange gamer with minimal storage devices. More
than 16 amps is required if your PC has more toys in it. For example,
if you bought an ATI X1900XTX, it draws 10 amps (part through the
PCI Express slot, part through the 2x3 PCI Express connector), and
you would need about 12V @ 23A to have a stable computer. So, enjoy
your new Ultra, but do not overload it.

HTH,
Paul

Thanks for the detailed reply Paul.

Just to confirm what you have said:

1. Plug the 20 pin ATX motherboard power cable into the 24pin socket
on the MB

then...

Sorry to be thick

Thanks

Pete

Sorry Paul, I just noticed that the spec on the side of the box is different
to the spec on their website.

This is what it says on the box, is this better for me or worse?

Thanks

Pete

+3.3VDC=16A
+5vDC=30A
+12vdc=19A 228W
-12vdc=0.6A
-5vdc=0.6A
+5vsb=2.0A






+3.3V

AC INPUT
115V/230V 10A/6A 60/50Hz
DC OUTPUT
+3.3V
+5V
+12V
-12V
-5V
+5VSB
500W
Max
Combined
Watts
28A
30A
34A
0.8A
0.3A
2A
500W

If the link in question is this one, the 34A rating on 12V is plenty.
Just plug it in and use it :-)

http://www.ultraproducts.com/product...roductID=2 98

HTH,
Paul