Forum: General Hardware
January 10th 15, 06:47 PM Posted to comp.hardware
|
Replies: 1
Views: 4,352
driver for Creative X-Fi won't compile
On a new machine I installed a SoundBlaster X-Fi Titanium card. I also
did # modprobe snd-ctxfi, and # lsmod | grep ctxfi shows:
snd_ctxfi 0
using it are sound_pcm, dec_hdmi,...
|
Forum: Gigabyte Motherboards
December 31st 14, 12:57 PM Posted to alt.comp.periphs.mainboard.gigabyte
|
Replies: 1
Views: 5,599
H97-D3H chip to send fan speeds?
On an older machine, the GA-EP45-UD3P motherboard has a Super IO chip
that transmits fan speed information via a it87 driver. But on a new
machine using the H97-D3H the chip has changed and I no...
|
Forum: General Hardware
December 5th 14, 10:10 PM Posted to comp.hardware
|
Replies: 0
Views: 4,208
lm-sensors not picking up fan speeds
I've installed debian Wheezy on new hardware. The case fans are Noctua NF-R8
PWM and the CPU cooler is Cooler Master Hyper EVO 212. The motherboard
is Gigabyte H97-D3H. Operating system is Debian...
|
Forum: General Hardware
November 30th 14, 08:14 PM Posted to comp.hardware
|
Replies: 0
Views: 4,033
Troubleshooting HD having an I/O error
I'm runing a new Linux machine with a Seagate Constellation ES.3
ST1000MN033 hard disk. I have had consistent freezes more or less 24
hours after booting, followed by a beep every minute. Once I also...
|
Forum: Gigabyte Motherboards
October 2nd 14, 01:39 AM Posted to alt.comp.periphs.mainboard.gigabyte
|
Replies: 3
Views: 4,852
memory timing setting
Paul writes:
Haines Brown wrote:
My 16 Gb Skill RAM says to set tCL to 9, tRCD to 9, tRP to 9 and tRAS to
24. When I boot a new board the BIOS by default has timing...
|
Forum: Gigabyte Motherboards
September 29th 14, 09:31 PM Posted to alt.comp.periphs.mainboard.gigabyte
|
Replies: 3
Views: 4,852
memory timing setting
My 16 Gb Skill RAM says to set tCL to 9, tRCD to 9, tRP to 9 and tRAS to
24. When I boot a new board the BIOS by default has timing set
automatically. But I see that it is setting tCL at 11, tRCD at...
|
Forum: Gigabyte Motherboards
September 19th 14, 05:52 PM Posted to alt.comp.periphs.mainboard.gigabyte
|
Replies: 5
Views: 5,065
SDRAM choice
Paul writes:
Haines Brown wrote:
Paul writes:
The dimensions in terms of the length of the modules, they
should all be the same length and pin...
|
Forum: Gigabyte Motherboards
September 19th 14, 04:27 PM Posted to alt.comp.periphs.mainboard.gigabyte
|
Replies: 5
Views: 5,065
SDRAM choice
Paul writes:
Haines Brown wrote:
In the past I've had no problem picking RAM according to motherboard
specifications and had no trouble, but this time the more I
...
|
Forum: Gigabyte Motherboards
September 19th 14, 11:58 AM Posted to alt.comp.periphs.mainboard.gigabyte
|
Replies: 5
Views: 5,065
SDRAM choice
In the past I've had no problem picking RAM according to motherboard
specifications and had no trouble, but this time the more I investigate,
the less comfortable I become.
I have a GA-H97-D3H...
|
Forum: General Hardware
September 14th 14, 08:17 PM Posted to comp.hardware
|
Replies: 0
Views: 4,292
Front panel filter replacement and fan removal
I using an old case because it is good quality, but ran into two issues.
The old 80 mm. fans are held in with I can only describe as plastic
"expansion bolts". I will replace the fans with better...
|
Forum: Gigabyte Motherboards
August 29th 14, 12:57 PM Posted to alt.comp.periphs.mainboard.gigabyte
|
Replies: 8
Views: 4,695
Power requirement for H97-D3H motherboard
Thanks for the correction Paul.
I wonder if I might slip in another petty question here regarding this
motherboard rather than start a new thread: can its Secure Boot be
disabled?
Haines
|
Forum: Gigabyte Motherboards
August 28th 14, 08:31 PM Posted to alt.comp.periphs.mainboard.gigabyte
|
Replies: 8
Views: 4,695
|
Forum: Gigabyte Motherboards
August 28th 14, 02:30 PM Posted to alt.comp.periphs.mainboard.gigabyte
|
Replies: 8
Views: 4,695
Power requirement for H97-D3H motherboard
Paul writes:
Haines Brown wrote:
I expect to purchase this motherboard, but am unsure about whether I can
use an Enermax 450 Watt power supply I happen to have in hand. I...
|
Forum: Gigabyte Motherboards
August 28th 14, 01:07 AM Posted to alt.comp.periphs.mainboard.gigabyte
|
Replies: 8
Views: 4,695
Power requirement for H97-D3H motherboard
I expect to purchase this motherboard, but am unsure about whether I can
use an Enermax 450 Watt power supply I happen to have in hand. I don't
plan to overclock the board or use it for gaming. The...
|