A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » Search Forums
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Showing results 1 to 14 of 14
Search took 0.00 seconds.
Search: Posts made by: Haines Brown
Forum: General Hardware January 10th 15, 07:47 PM Posted to comp.hardware
Replies: 1
Views: 4,068
Posted By Haines Brown
driver for Creative X-Fi won't compile

On a new machine I installed a SoundBlaster X-Fi Titanium card. I also
did # modprobe snd-ctxfi, and # lsmod | grep ctxfi shows:

snd_ctxfi 0

using it are sound_pcm, dec_hdmi,...
Forum: Gigabyte Motherboards December 31st 14, 01:57 PM Posted to alt.comp.periphs.mainboard.gigabyte
Replies: 1
Views: 5,201
Posted By Haines Brown
H97-D3H chip to send fan speeds?

On an older machine, the GA-EP45-UD3P motherboard has a Super IO chip
that transmits fan speed information via a it87 driver. But on a new
machine using the H97-D3H the chip has changed and I no...
Forum: General Hardware December 5th 14, 11:10 PM Posted to comp.hardware
Replies: 0
Views: 3,939
Posted By Haines Brown
lm-sensors not picking up fan speeds

I've installed debian Wheezy on new hardware. The case fans are Noctua NF-R8
PWM and the CPU cooler is Cooler Master Hyper EVO 212. The motherboard
is Gigabyte H97-D3H. Operating system is Debian...
Forum: General Hardware November 30th 14, 09:14 PM Posted to comp.hardware
Replies: 0
Views: 3,759
Posted By Haines Brown
Troubleshooting HD having an I/O error

I'm runing a new Linux machine with a Seagate Constellation ES.3
ST1000MN033 hard disk. I have had consistent freezes more or less 24
hours after booting, followed by a beep every minute. Once I also...
Forum: Gigabyte Motherboards October 2nd 14, 01:39 AM Posted to alt.comp.periphs.mainboard.gigabyte
Replies: 3
Views: 4,463
Posted By Haines Brown
memory timing setting

Paul writes:

Haines Brown wrote:
My 16 Gb Skill RAM says to set tCL to 9, tRCD to 9, tRP to 9 and tRAS to
24. When I boot a new board the BIOS by default has timing...
Forum: Gigabyte Motherboards September 29th 14, 09:31 PM Posted to alt.comp.periphs.mainboard.gigabyte
Replies: 3
Views: 4,463
Posted By Haines Brown
memory timing setting

My 16 Gb Skill RAM says to set tCL to 9, tRCD to 9, tRP to 9 and tRAS to
24. When I boot a new board the BIOS by default has timing set
automatically. But I see that it is setting tCL at 11, tRCD at...
Forum: Gigabyte Motherboards September 19th 14, 05:52 PM Posted to alt.comp.periphs.mainboard.gigabyte
Replies: 5
Views: 4,699
Posted By Haines Brown
SDRAM choice

Paul writes:

Haines Brown wrote:
Paul writes:
The dimensions in terms of the length of the modules, they
should all be the same length and pin...
Forum: Gigabyte Motherboards September 19th 14, 04:27 PM Posted to alt.comp.periphs.mainboard.gigabyte
Replies: 5
Views: 4,699
Posted By Haines Brown
SDRAM choice

Paul writes:

Haines Brown wrote:
In the past I've had no problem picking RAM according to motherboard
specifications and had no trouble, but this time the more I
...
Forum: Gigabyte Motherboards September 19th 14, 11:58 AM Posted to alt.comp.periphs.mainboard.gigabyte
Replies: 5
Views: 4,699
Posted By Haines Brown
SDRAM choice

In the past I've had no problem picking RAM according to motherboard
specifications and had no trouble, but this time the more I investigate,
the less comfortable I become.

I have a GA-H97-D3H...
Forum: General Hardware September 14th 14, 08:17 PM Posted to comp.hardware
Replies: 0
Views: 4,012
Posted By Haines Brown
Front panel filter replacement and fan removal

I using an old case because it is good quality, but ran into two issues.

The old 80 mm. fans are held in with I can only describe as plastic
"expansion bolts". I will replace the fans with better...
Forum: Gigabyte Motherboards August 29th 14, 12:57 PM Posted to alt.comp.periphs.mainboard.gigabyte
Replies: 8
Views: 4,330
Posted By Haines Brown
Power requirement for H97-D3H motherboard

Thanks for the correction Paul.

I wonder if I might slip in another petty question here regarding this
motherboard rather than start a new thread: can its Secure Boot be
disabled?

Haines
Forum: Gigabyte Motherboards August 28th 14, 08:31 PM Posted to alt.comp.periphs.mainboard.gigabyte
Replies: 8
Views: 4,330
Posted By Haines Brown
Power requirement for H97-D3H motherboard

Paul writes:

Haines Brown wrote:
Paul writes:

Haines Brown wrote:
Thank you for your very interesting and informative reply. I did the
best...
Forum: Gigabyte Motherboards August 28th 14, 02:30 PM Posted to alt.comp.periphs.mainboard.gigabyte
Replies: 8
Views: 4,330
Posted By Haines Brown
Power requirement for H97-D3H motherboard

Paul writes:

Haines Brown wrote:
I expect to purchase this motherboard, but am unsure about whether I can
use an Enermax 450 Watt power supply I happen to have in hand. I...
Forum: Gigabyte Motherboards August 28th 14, 01:07 AM Posted to alt.comp.periphs.mainboard.gigabyte
Replies: 8
Views: 4,330
Posted By Haines Brown
Power requirement for H97-D3H motherboard

I expect to purchase this motherboard, but am unsure about whether I can
use an Enermax 450 Watt power supply I happen to have in hand. I don't
plan to overclock the board or use it for gaming. The...
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT +1. The time now is 11:17 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.