HDD got bad sector in MBR
 

Is there any possibility to mark this sector as unreadable and move
(make new) MBR in the other area of the HDD??
It can't be detected when I connect via USB cable to the WinXp.
The HDD is Seagate Barracuda ATAIII ST340824A
--
ven

HDD got bad sector in MBR
 

venioo wrote

Is there any possibility to mark this sector as unreadable and move (make new) MBR in the other
area of the HDD??

Yes, the hard drive manufacturer's diagnostic should be able to make the drive do that.

That will usually lose all data on the drive tho.

You should be able to force the drive to remap that sector
by writing just that sector to the drive with an MBR ute.

It can't be detected when I connect via USB cable to the WinXp.
The HDD is Seagate Barracuda ATAIII ST340824A

Simplest to use Seagates SeaTools, but that may lose some data because its unlikely
that just that sector has gone bad. Its much more likely to be more than one.

HDD got bad sector in MBR
 

Previously venioo wrote:
Is there any possibility to mark this sector as unreadable and move
(make new) MBR in the other area of the HDD??

No. If the MBR are is unreadable, the HDD is unusable.
Your only hope is to get the HDD to transparently
replace it. Typically overwriting it will do that.

It can't be detected when I connect via USB cable to the WinXp.

Well, WinXP is a toy that will bail out on a lot of
not really serious problems. Are you sure the MBR sector is
bad?

Armno

HDD got bad sector in MBR
 

SeaTools helped!
Many bad sectors found but HDD is still useful for keeping less
important things such as .jpg or .mp3 :)
THANKS-A-LOT!!!
--
venioo

HDD got bad sector in MBR
 

"venioo" wrote in message
...
Is there any possibility to mark this sector as unreadable and move
(make new) MBR in the other area of the HDD??
It can't be detected when I connect via USB cable to the WinXp.
The HDD is Seagate Barracuda ATAIII ST340824A
--
ven

Try the following.

In Windows Disk Management, try assigning a drive letter to the drive, do
not reformat.
That might fix the MBR, and, if you are lucky, all files may still be
intact.

--
http://www.standards.com/; See Howard Kaikow's web site.

HDD got bad sector in MBR
 

"Arno Wagner" wrote in message
Previously venioo wrote:
Is there any possibility to mark this sector as unreadable and move
(make new) MBR in the other area of the HDD??

No.

Yes.

If the MBR are is unreadable, the HDD is unusable.
Your only hope is to get the HDD to transparently
replace it.

Typically overwriting it will do that.

See.


It can't be detected when I connect via USB cable to the WinXp.

Well, WinXP is a toy that will bail out on a lot of not really
serious problems. Are you sure the MBR sector is bad?

Armno

HDD got bad sector in MBR
 

Howard Kaikow wrote:
"venioo" wrote in message
...
Is there any possibility to mark this sector as unreadable and move
(make new) MBR in the other area of the HDD??
It can't be detected when I connect via USB cable to the WinXp.
The HDD is Seagate Barracuda ATAIII ST340824A
--
ven

Try the following.

In Windows Disk Management, try assigning a drive letter to the
drive, do not reformat.
That might fix the MBR,

Not a chance, the diag says its got lots of bads.

and, if you are lucky, all files may still be intact.

Not those which have a bad sector in them.

HDD got bad sector in MBR
 

I have a Barracuda ATA Model ST340824A and need to get a USB to ATA
adapter cable to see what I can pull off this old drive. Any idea which
is the correct adapter to buy would be?

HDD got bad sector in MBR
 

Mordinaky wrote:

I have a Barracuda ATA Model ST340824A and need to get a USB to ATA
adapter cable to see what I can pull off this old drive. Any idea which
is the correct adapter to buy would be?

Any one that has 3.5" ATA?

Arno
--
Arno Wagner, Dr. sc. techn., Dipl. Inform., CISSP -- Email:
GnuPG: ID: 1E25338F FP: 0C30 5782 9D93 F785 E79C 0296 797F 6B50 1E25 338F
----
Cuddly UI's are the manifestation of wishful thinking. -- Dylan Evans