|
|
Bob Headrick; ? on 7960 by
ET
Is there a preferred way to tell which of the three cartridges (#56,
57, or 58) would be at fault? When changing cartridges (refilled) and
the calibration printing is done, there may be a color(s) missing or
the color may be faint. Normally, I change both #57 & #58 at the same
time and end up...
|
|
7 |
609 |
|
|
Problem with OKI Microline by
Vincent Derrien
Hello,
I've a OKI Microline 320 Elite printer on Windows 2000 connected to
LPT1. To print a document, I'm using (as indicate by OKI) the generic
driver Epson LQ-850 or IBM Pro Printer III.
I must print, in my application, a document in 15 CPI. For this, I've
configured the printer in 15 CPI. The...
|
|
0 |
342 |
|
|
need help connecting new printer to XP pc via ethernet by
Raspy
I just got a new Brother all-in-one printer. It has an ethernet connection
(along with USB). I'm running low on available USB ports and I'm not using
the ethernet connection on my Dell, so I thought I'd try to set it up via
ethernet. The manual that came with the PC doesn't give any info on...
|
February 26th 05 04:46 PM
by jbuch
|
1 |
498 |
|
|
HP color laserjet 9500 by
DaKing
Hello,
We're thinking about buying a HPCL9500. Does anyone has some experience with
this type of machine.
Is it a good buy ? Or do you advice another machine ? Just wanted to make
sure we do/buy the right thing...
Thx for the info,
DaKing
|
|
3 |
426 |
|
|
|
February 26th 05 09:20 AM
by Ah Ben
|
0 |
623 |
|
|
Lexmark 705 paper feed by
Hans
When I print one page, the software window says two pages needed and then
after completing the printing job continues to feed an empty page. If only
one sheet of paper is in the feed, it will say that my paper feed is empty,
asking for an additional page.
Where have I gone wrong?
Thanks in...
|
|
1 |
513 |
|
|
Brother LC800 or LC31 Cartridge by
Sierra
Does anyone have a link showing how to properly refill one of these? I'm
getting ink everywhere but very little in the cartridge, the spong doesnot
seem to absorb the ink
thanks
|
February 26th 05 06:10 AM
by Sierra
|
2 |
465 |
|
|
Cannot create DIHPAiOFaxManager object Error message by
grkumar
When I click "send a fax" on the HP Director I receive the message
"Cannot create DIHPAiOFax Manager object". I have no clue what that
means. This is a new message I have not received before.
I uninstalled and reinstalled my all-in-one printer, which took me
forever.
I have run the fax wizard...
|
February 26th 05 05:17 AM
by grkumar
|
0 |
277 |
|
|
HP1000Laser and XP reinstall question please by
Dudley Henriques
I want to make absolutely sure I have this right before I do it on
Monday.
I'm doing a reinstall of XP and I have a HP Laserjet 1000 printer. Since
new, I have downloaded several driver updates from HP, and have them
installed. I'm puzzled on one issue. I started out with the drivers
supplied on...
|
|
0 |
479 |
|
|
|
|
0 |
391 |
|
|
Lexmark Z22 Alignment Issues by
timmac
Hi all, I'm hoping someone might have some advice or can point me in
the right direction. I have a Z22 color inkjet printer, which I just
started using again after several months of not using it. Now, I've
installed new cartridges, but when I try to do the alignment, all three
of the horizontal...
|
February 25th 05 05:40 PM
by Harvey
|
2 |
444 |
|
|
Personal Laser Printer by
Mark
Hello- I need a recomendation for a personal laser printer. Here's what I
need:
1. Parallel port
2. Non-GDI- I need to connect this printer to some industrial equipment that
has a proprietary operating system -PCL 4 would be nice- But I at least need
the ability to dump ASCII text to the parallel...
|
February 25th 05 02:37 PM
by Mark
|
3 |
314 |
|
|
|
|
2 |
437 |
|
|
HP7310 by
Guy Hollins
Hi
Anyone have one of these and if so does yuors suffer from bad banding
|
|
2 |
338 |
|
|
|
February 25th 05 07:38 AM
by Sierra
|
3 |
420 |
|
|
2 Printers, 1 PC by
Rob in NJ
I just got a new USB printer. Can I hook it up to my PC while my old
Parallel printer is hooked up? Will the PC recognize both? IS THIS A
DUMB QUESTION?!?!
Thanks-
Rob in NJ
|
|
6 |
267 |
|
|
Epson RX500 printer problems by
[email protected]
I've had this printer for approximately 6 months with no problems.
I've just recently replaced my printer cartridges with generics and
although did not have any problems initially, now I cannot get the
magenta (486) to clear up, I get vertical banding in anything that I
print. I have tried to...
( 1 2)
|
|
11 |
720 |
|
|
lexmark 1100 by
lamberthenri
I find it quite unbelievable that for only a little broken plastic part that
hold the cartridge in place,Lexmark is telling me to scrap my new printer
and buy a new one.They say that they dont supply spare parts for certain
models of printers.What a wasteful corporate attitude.If you can help...
|
February 25th 05 01:40 AM
by Harvey
|
2 |
227 |
|
|
HP Laserjet 5M - loses formatting by
Kindrick Ownby
HP 5M printing remotely from an IBM System/36.
Print program generates pseudo escape sequences at beginning
of file for simple items like compressed or normal print, font,
etc. The System/36 disallows non-printing characters in a print
file - some device or software between the Sys/36 and the...
|
|
0 |
275 |
|
|
Epson 440 banding question by
MikeD
Yes, I know it's an old printer and I should chuck it in the bin, but before
I do I would like to find out why the printouts have a faint banding effect.
The head alignment pattern and nozzle check are OK. The lines are spaced at
about 0.03" when printing at 720dpi, and they run in the direction...
|
February 25th 05 12:58 AM
by kzza
|
6 |
397 |