Is it possible to change the multiplier in the bios of Gigabyte's GA-7VM400AM with VIA KM400A chipset? Maybe in the advanced options? www.gigabyte.de/MotherBoard/Products/Products_GA-7VM400AM.htm I possess the GA-7N400Pro2 and there you can change the multiplier via a dipswitch on the motherboard...

Hi folks, I'm building a low-noise computer based on a µATX mobo. The Biostar M7VIZ looks pretty interesting. I need SATA-controller onboard, AMD Athlon XP-M support and adjustable CPU voltage at the bios. Does anybody has this board or even knows whether it provides the features showing above.

Hi folks, which Athlon 2500+ are best for overckocking? AQEXA, AQZFA, AQYFA etc... thx Christian

Hi folks, I'm going to buy an Asus A7N8X-BlaBlaBla MoBo. But I'm not sure which chipset to take... Which nForce chipset is the best? -nForce2-S -nForce2-ST oder -nForce2-400

Hi, I got my hands on an AMD K6-2 400 with one pin missing. The pin is a Vcc2 pin (AN 19 to be exact). My question is: Is this pin absolutely essential to safe and stable operation, or will it be possible to run without it? Thanks.

exaqctly what the topic says AMD Athlon XP 2600 333 mhz FSB and 512 l2 Cache I believe the Intel Celeron is as follows Intel Celeron 2.8 ghz 400 mhz FSB and 128 l2 cache which one do you think would perform better on an overall basis including

AXDA3200DKV4E got this code would just like to know before i purchase Thanks for help (in advance) chris

not had to apply this in the past, as it has came pre applied on my hs/fans do i apply it to the bottom of the heatsink or to the top of the processor? there are 4 circular rubber like pads on the processor that the hs/fan sits on should i place it in the middle of these 4 pads? the thermal paste...

I have probably asked this question sometime here in the last few days it will be burried amongst the threads now so sorry if i am duplicating a question (im sure that happens alot on usenet) But can mobile Athlon XP's with an unlocked multiplier be used on a standard socket A board? and with a...

ok setup Abit NF7 v2.0 motherboard AMD 2600+ XP barton 333fsb I have tried in softmenu III to enable to user set CPU permaters I have had the following permaters

my CPU has an FSB of 333 mhz (Athlon 2600+) my board will support FSB of 400 mhz I cant set the FSB to 200 mhz (400 mhz all together) because the CPU is only 333 mhz I am therefore right in assuming i need to change the multiplier with the FSB always at 166 mhz

there is a version of the NF7 called nf7 v2.0 (i am not at all referring to nf7-s in anyway) i just would like to know if there is any way of identifying if my nf7 is infact a 2.0 or not, mainly because the 2.0 supports fsb of 400 mhz and the other only supports 333

do the amd 64 bit processors come with a heatsink and fan when you buy the retail box package? if so is it anygood when not overclocking i assume it would be no good when overclocking?

does the amd XP-M (mobile) fit into any standard skt A motherboard? -- Thanks, Chris.

the standard clock for a processor has always been mhz/ghz... the AMD XP processors dont use this method do they? the AMD XP 2800 isnt 2.8 ghz or 2800 mhz is it? so can anyone tell me how you would go about working out the ghz for the AMD XP processors?

I currently have the following spec: AMD XP2600+ BARTON AMD STOCK HEATSINK 1.5 GB DDR RAM ABIT NF7 v2.0 Motherboard (nForce2) with softMenu III

I am new to all this and haven't tried any overclocking yet but am looking too, I am currently using an AMD XP2600+ with the stock heatsink, the temp idle middles at about 45 C it does reach peaks of 55 - 58 C just wondering are these high peaks in the mid to late 50's normal or is it a bit hot? I...

could i get a lower CPU temp if i got a different fan/heatsink? if so any reccomendations?

I am planning on buying this setup (KT400 and AMD 2600) am totally new to overlocking and have no idea... can anyone point me to a website that will explain things or instruct me? as for the setup with the Kt400 is that ok to OC with an AMD 2600 or 2500 mobile?

ok have an AMD2600+ (1.92ghz) with locked multiplier, just replaced stock fan with coolermaster vortex dream 7 so i thought what the hell with the stock the CPU idled at 53 C which was poor to say the least popped in new coolermaster, idles at 44 C, thought i would OC it i am now running fine as...