Hi, Just got back from vacation and went to boot up an old machine with a BE6-II mother board. First it made an alarm sound. I checked to make sure the voltage wasn't set to 200 and it wasn't. I tried removing the RAM and that had no affect. I finally ended up fiddling with the ribbon cable to the...

Question: I set the max3 CMOS Memory Clearing Header to 2-3 and then tried to power up the board. I take it that's not a good idea. Now it won't power up at all... Any ideas why?

Here's the problem. my wifes PC WAS working absolutely fine most of the time but more and more often it started to switch off with NO warning at all. It then would'nt even POST when I attempted to restart. No bios screen no hard drive activity no CPU fan. The PSU fan would be on and the RED HD...

Hi. I have mb abit Nf7-s version 2.0 Where can i find a list of compatibile ram? Thanks Xpost: news:alt.comp.mainboards.abit, news:alt.comp.periphs.mainboard.abit F/up2: news:alt.comp.mainboards.abit -- Joey: "Ti va di ballare?" Pacey: "Certo. (ballano) Perché ora mi sento così bene" Joey: "Forse...

Hi Has anyone any understanding on this board mine is possesed! WiLd

Hi, I just recently got a postcode of 83 after an unexpected shutdown. I've reseated memory and Video Card and still get the 83 Postcode. I've jumpered the CMOS and removed the battery and still get this error. What other steps should I try? Fatal1ty AN8 AMD Athlon 64 3500+ CORSAIR XMS 1GB (2 x...

I have a mobile rack HD, that I carry around. When I use in the pc with abit motherboard (see subject, no raid in place), the HD becomes extremly hot, as compared when I use it with the other pcs. This sounds strange, since the place where it is inserted in the cases is always the same. Is there...

When I boot, I get a messsage: Press F1 to continue or Escape for Bios Soft Menu. I'd like to get rid of the annoying message so my machine can continue to boot w/ou interruption. Everything in the bios looks OK according the the manual (Abit IT7). I have not tried "Optimize Defaults". Is there...

Just bought an NI8 SLI mobo. Did the following: - Connected it up with ALL THREE power connectors (ATX12V1, ATX4P1, and ATXPWR1). - Installed my CPU with stock cooler and connected to CPUFAN. - Installed my memory. - Setup the SLI bridge connector on the mobo to NORMAL - Installed my graphics...

I have an ABit NF7-S and windows XP pro (tried both service packs and a Bios upgrade) I cannot seem to get suspend to ram working Ive tried both settings in the bios, but i always just get windows suspending to disc i really want suspend to ram working. Is this a problem with this board or am i...

I currently have an ASUS P4P800-VM. What I would like is a dual P4 ASUS P4P800-VM with onboard raid controller. I know this doesn't exist. I don't know who to ask and am hoping that someone can help me out. I've listed what I think is what I want: - dual xeon 2.4 GHz - 3.2GHz each - 800 MHz FSB (I...

I am running on OC'd NF7-S v2.0 and get the occasional stutter? Should I back off my FSB speed? Increase the chipset voltage? Any ideas?

Sorry if this has been covered before, I'm new to this group... I've just built up a system using an IC7-G with a P4 3.06 (533fsb) and standard Intel cooler, carefully applied using good fresh compound, fan spinning at about 4000rpm... On boot-up from cold the bios shows the CPU temp at about 65...

Hi everyone, I need to upgrade my graphics card (Geforce 2 GTS) and would like some recommendations from others who have this board (plain KT7). Thank You smilodon

Hi How i build a raid-0 with this board? I have 2 Maxtor 40GB HD's same type. Jumper oc CS? On one ide cable? thx Jörn

hi, i want to make a pc for my daughter. got myself a SE6 and a matrox g-400marvel when i install w98se the system restarts everytime it's at the point of updating the drivers (searches for p&p moonitors and ................restarts) anyone got an idea what could be wrong?

Hello, I have just built a new system using the IC7 motherboard. Windows XP Pro has been installed without any problems. However, I am having a bit of difficulty in getting RJ-45 LAN connector to work. There seems to be no reference of it in 'device manager' nor is there a switch in the bios...

I have a KT7A-Raid board, with a 1 GHz Athlon processor and 768 MB PC-133 RAM, running Win 98SE. I have run this board configured with Raid-0, but I'm now just using it without the Raid function.... but I do have 4 WD drives on it. The system has just recently started having a problem with locking...

How to use the nf7-s rev2 irda port ?

Hi, I have a TH7-II RAID motherboard which refuses to shut down via software, forcing me to flip the power switch or pull the plug each time I want to switch it off I'm running XP Pro, but the same problem occurs with other OSs. I've also tried two different cases, both with same results. The...