Hi! If you have a MEA110 toshiba mp3 player or any other toshiba mp3 player, and you have an SD card reader - could you please tell me how the music is stored on the card? I've lost my cable and Toshiba support is absolutely useless. THANK YOU VERY VERY VER MUCH.!

Does anyone know where I can sell a couple hundred or so used DLT IV tapes and some used DLT III media. I've heard that there's some type of market for used media but can't seem to find anyone buying right now. Any help is appreciated J.T.

What kind of DDR-SDRAM is appropriate for Pentium 4 (2.4 GHz) and use of graphical programs (such as Photoshop)?

I heared that rate of transmission of files in HDD with ATA-100 is 100 MB/s but I tried this and measured its speed about 4 MB/s. Which is correct and why?

didn't know where to write... When I try to Install Kazaa Media Desktop I get a message in a little box when the Install shield wizrd is preparing...saying Internal failure Error number 0x8002802B Can't find the element and then another message comes up after I have closed the first

ok so its actually upgrade time... but id also like the community that ive give soo much to, to give a lille back to me (A) :) ok so im plannin on that illusive upgrade... the processor im still not sure about... input appriciated (ok i know this is a heated topic.. but im still lookin for more...

I have a Cybernetic Data Products Model SDT 1204M in need of repair. It does not seem to be electrical and haven't any luck (yet) in finding anyone to attempt to repair it. Any and all information would be great! JMW

can i replace a drive in an external firewire box (frrecom)? hi there all I have an external cdrw from freecom (firewire). I would like to replace the drive inside with a dvd writer or perhaps a HD. Is it possible? would winXP recognise the drive or is it dependent on some bios in the...

If you can read cd's but not write to them, try enabling DMA on the ide channel that your burner is on. The IDE Channel was set to Autodetect in my BIOS. This means that the BIOS was probably choosing DMA mode for it, I heard a few people had this problem and they said the way around it was...

Hi all, I would like to have my logitech optical mouse set to have the right click be the primary click. When I change the setting in the mouse properites it works fine until I log off. Once I log back in, it goes back to the regular way. Is there some way to make this the default setting? ...

Sorry , I changes my code to Input ....... So please read SR_DATA_IO_int (13 downto 0) as Input (13 downto 0) Cheers Isaac Allan Herriman wrote in message ... On 9 Jul 2003 11:00:32 -0700,...

I am building a new computer with a Leadtek k7ncr18gpro2 mother board, AMD 2700+, 512 PNY memory. I intalled XP professional and now when I start up it will only take a few minutes until the system forces a restart and automaticlly restarts on me. I am not sure what is going wrong? I was wondering...

Hello, I need the driver for my ethernet card. I think Compaq uses a little bizzare setting for network card, so I check their website to find the driver, but couldn't. After checking the spec of my model, I found out that my ethernet card was Realtek 8201BL, which, according to the information...

Howdy, Assembling a PC, have done this several times on PIII/Celeron systems without a hitch. Purchased a used 2.2 GHz P4 socket 478, 400 MHz FSB, used motherboard socket 423, and a socket 478 to 423 adapter. The MOBO does not have onboard graphics, so I have a graphics card installed. The case...

I have a Shuttle AK32 Mainboard that supports 266Mhz. The CPU Support list shows support up to Athlon XP 2600+. However, I have access to a 2500+ (1.83Mhz) Barton CPU that runs at 333Mhz. Will it run OK? At what speed will Actually run at? TIA

(bulzai13) wrote in message ... please tell me website that can help me to repair my monitor.my monitor have a problem that i cant solve by my self i.flashback motherboard is burn. i hope someone can help me to find with...

Mine is ENERMAX front panel ref UC-A07FATR2 (Thermal control panel). I hate cross-posting but this appears to be an alert since you can damage your hardware. This week I fried my CD burner because of the inversion of the +12 & +5V wires at the output of the ENERMAX module T-Power cable, my CD...

Im looking to drop about $2,000 on a new gaming box. I have decided on just about everything except graphics card. I am somewhat loyal to nvidia, but not as loyal as I am to say Coca-Cola, if you know what I mean. I am slasobuying a mobo with the nforce chipset, which is, of course, created by...

System Intel Pentium4 2.8c GHz GIGABYTe GA-8KNXP F5 2X512 MB RAM Samsung DDR PC 3200"KH560838E-TCCC" ATI 9600 Pro128 MB RAM when i run any RealOne player files the system just hang! evein after

Hi Fellows, How can I synthesize multiple file one by one using xilinx compiler in MAKEFILE script. I have done using only one file but when I enter multiple files in "VHDL= ....." field thenI get the following error. make: *** No rule to make target `VIR3.vhd,VIR3_1.vhd,VIR3_2.vhd Rgds