Any ideas on how to overclock a 1.1 GHz Celeron processor? My warranty is expired and I'm looking for a free (or at least cheap) performance boost. I can't find anything on my exact processor speed (though I've seen info for 1.0 and 1.2 GHz Celeron). I don't know my FSB speed, but I think it's...

I've just bought and built a new pc consisting of: Asus A7N6X Deluxe m/b AMD Athlon 2500 Barton cpu with AMD fan and heatsink Antec case and 340w psu 512Mb Crucial pc2700 DDR ram (2 x 256Mb) Maxtor Diamond max 120Gb SATA h/d ATI Radeon 9600 Pro AGP card 128mb Windoze XP os

To bad this mathematical whizz can't count.

Does the HP Vectra VLi8 motherboard allow overclocking?? I've heard somewhere that the HP Vectra motherboard is a BX440 derivative. Does that motherboard allow overclocking?? I have a Pentium III 450MHz and I want to overclock it to 500MHz or 550MHz. I've read the specs for the Vectra on hp's site...

Hi, I used nvflash to flash the bios of ti4200 and everything was fine until i reboot... black screen (the monitor is ON and not in power saving mode...), no post beep, and no boot... then i plugged a pci video card and i tried to flash my agp card (chaintech a-gt20), but nvflash displays an error...

Hi, I used nvflash to flash the bios of ti4200 and everything was fine until i reboot... black screen (the monitor is ON and not in power saving mode...), no post beep, and no boot... then i plugged a pci video card and i tried to flash my agp card (chaintech a-gt20), but nvflash displays an error...

Hey Dave, "kony" wrote in message ... On Mon, 14 Jul 2003 13:14:44 +1200, "~misfit~" wrote: Hi Spajky, I'm about to put a celly 900 coppermine in a slocket in one of my 6163

I bought a water cooling kit from maplin in the UK but the instructions are useless (Translated from japanese I think), so I don't know how to set it up at all. the URL for the kit is http://www.maplin.co.uk/products/module.asp?CartID=448118&moduleno=32469&Products=1 I also bought a large radiator...

I have the following a7v266-e (asus) xp1700 palimino ati 8500 512 genaric 2100 ram I cant seem to get past 148 fsb, temps are 50c while under load. even at 149 fsb crash hear ther everywhere, same temps. if I were to use say pc2700 ram chips would that help???

I bought this very efficient cooler after a review I read on tom's. However the fan mounted on top of the CPU makes a noticeable vibration. When it speeds up to it's some 4000 rpms it starts to shake back and forth, oscillate I think, and it both makes an low but audible drone, it creates...

Hello, I've tried to overclock my ti 4200 (INNO : 250/446 ) with Nvidia 41.09 drivers. Without overclock, I'm around 12 500 pts with 3mark 2001, but with overcloack to 380/500 I only got 10 500 pts to 3dmark 2001. What's wrong, please ??? (with simple words, I'm french, thanks) Config :

The correct model is CNPS7000-AlCu? J. "John Smith" wrote in message ... Also, have these ones now replaced the flower as the 'better' coolers in terms of noise? Or did the flower occupy too much room?

Hey all, Well I f**ked up and broke one of the tabs on the processor socket that the HSF clip hooks onto. Running a MSI 815E Pro board with a 1GHz PIII. Can someone recommend one that uses the other tabs to secure the clip?? Does one exist?? I don't need anything fancy. Just something that would...

Hi, I'm trying to use 2 x 256mb twinmos dimms with ch-5 winbond chips in dual ddr mode on my asus p4p800 motherboard. However whenever the dimms are in a dual ddr configuration the machine refuses to boot with a 2:3 (266mhz) memory divider. I can use the (333mhz) 4:5 divider but my fsb max's out...

The fan on my Asus GF4 4400 decided to die. I bought a Thermaltake Crystal ORB but have had problems fitting it. Wondering if anyone else has tried this combination. I removed the the OEM? fan from the card. It was attached by 2 holes maybe an inch away from the chip. Around the chip were 4...

Hello, I've installed water cooling on my CPU. I have raised the FSB to 155 (from 133) and this is about the highest I can go without the computer freezing on startup. However, since I have water cooling installed, the CPU temperature will hardly ever go above 40 degrees C, which is well within...

Wayne Youngman wrote: Hi, I am researchng the parts for a new machine (AMD 2500+ ABT NF7-S) and have heard good things about TwinMOS. . . . But which sticks should I choose? I intend to try for a 400MHz FSB overclock at least,

have DEll Laptop latitude cpxH500gt running on Xp PRO and my mainboard chipset is intel 440bx/dx/zx vendor 8086...but i cant finl pLL manufacturer or manufacturer who created my mainboard......just chipset name..... i tried to open my latpop too se mainboard but couldnt find manufacturer nither...

I'm currently using a Packard Bell setup, (all original bits.) It's using an ms-6340 mobo, (with onboard graphics.) Trouble is i've recently updated all my drivers to get the graphics chip running properly, (from the Packard Bell site,) but i'm experiencing some problems......... When the...

I should be happy with a stable 2.94 ghz, just wondering if it is still a setting holding me back. ... 8. CPU voltage = default - Stock heat sink/fan - CPU temp = 46 degrees ... I saw your other post. Why don't you increase your CPU volts? Go straight for 1.65/1.675. Std sink/fan will...