Is there a OC utility that will load at start up or are they set up manually? Do the ATI Radeons that come with 3.0, 3.3 and 3.6 ram chips overclock differently???

On front side of my Hercules Radeon 9800 (non-PRO) is situated little (cca. 3x4 mm) switchbox near fan connector with two small switches (lever-like) with description ON and KE up and 1 and 2 down. Does anybody know what is that? I'm kinda curious, but not enough to try it. Thanks for any info...

I have an ecs L7S7A motherboard and Amd athlon xp "barton" 2500+ . Ram Im going to upgrade to 512 3200 ddr ram. Can i get some overclocking help? ANy references?

Pls help: 20 to 30% performance increase here, but... Stabile at 2D, but drops to desktop after about 1 minute or 2 at 3D (PC mark2001 or CoD) . Since FBS 133 FBS ( before 100 ) I can´t see any PCI or AGP bus speeds anymore with prgs. I´m quite sure, could see PCI or AGP bus speeds before changing...

does this motherboard support hyper threading?

Trying to GOOGLE to find out just what some of the BIOS settings on my Asus P4C800-E Deluxe mainboard do, but all I'm finding are overclocking stats... Basically, I'd like to find a site that explains the following in by BIOS: - DRAM burst length - DRAM idle timer - DRAM refresh rate - ICH...

For some reason or another, I cannot overclock, not even one mhz, without encountering the problem of the Intel RAID controller not recognizing my 2 120gb Western Digital hard drives in a RAID-0 array. I have a 2.6c with stock cooling on an Abit IC7-G. I've never used RAID before on any...

the p4 stock cooler has a metal pad and graphite on it. When removing the cooler obviusly the graphite came off. If i reapply some paste should i remove the metal pad or leave it on and just apply a really thin layer of paste.? Simon

My system: p4p800dlx P4 2.8ht corsair 2*513 pc3700 dual, channel running DDR400 OC'ed @ 236 system bus (3.3ghz) 1:1 cpu/ram mam enabled

Hi All, CPU-Z ver 1.19a only recognizes these sticks as 'Corsair DDR-SDRAM PC3700' I am also running an ASUS P4C800 Deluxe MB (1014.003 BIOS rev) and it thinks they are DDR400 !! Anybody know whats going on ?

Hi, I have a P4 2 gig processor and an asus Mobo how far can I OC and still remain on the safe side? Thanks, Pete -- P§³

Ahh disconected my Vantec Fan controler, needed to find a serial for a return, had a look at my temp and @(@**(@ 68c, pluged all the wires back in and 12volted each fan, and back to normal 52c at the momment, 7volts it runs like 55 to 60 on a coolish day, in summer in Australia.

Does anyone know what the maximum safe voltage a P4 2.4C can be run at, for I have spent many hours on the web but have not found a definitive answer. I have OC'd to 3.1 but running prime95 shows errors, which at lower speeds I have managed to remove by uing the VCore. Yet I am at 1.59v now and...

Placement of the PSU is this important for cooling ? I have the PSU in my case right above the CPU, even though their is space above it for it, just have to cut a hole and add a bracket to install it their, the cables are long enough to plug everything in and all. I just read somewhere AMD site...

Hi all My P4 2.66 runs between 44 and 58 degrees (0-100%) and about 46-61 degrees when o/c to 3.0Ghz .Runs like a dream but was wondering are these figures typical? Also,I read a post somewhere that described "lapping" of the heatsink.What is this technique? TIA

"martini" wrote in message ... P4G8X Deluxe with P4 2.53 Ghz non overclocked stock intel cooling my cpu idles at about 43-45 degrees my motherboard without any extra cooling idles at 38! when i put in a fan at the bottom of my...

My watercooling setup has started to make a lot of noise - specifically the pump. I haven't changed the water or done anything to it in about a year or so. When I started it up, I added the water-wetter and stuff that is supposed to keep the green stuff from growing in it. But, I think it may...

I picked up a couple of 10gph Italian centrifugal circulating pumps from www.surpluscenter.com for $20 each. (their item # 2-1202) They look like they may have been made to work in a dishwasher or maybe a small Jacuzzi. I modded one with PVC pipe fittings and some epoxy putty so it has 1/2" ID...

Solo per questa settimana ho ha disposizioni le seguenti configurazioni: Case - P 4 con alimentatore da 400 Scheda mad Asus P4BE-SXE - FSB 800 mhz "ottima per overclock" Processo Intel Pentium 4 - 2.60c Ghz hard-disk: Maxtor 120 Gb - 7200 Rpm, 2 mb buffer Mb: 512 ddr - 400mhz Scheda video:...

Just want to get the cpu cooler thats all in australia it gets 45c in summer and it runs 60c+ at load would like it to be about 5c lower or so. Thanks.