If the case meets ATX specifications and the power supply meets ATX specifications, then the power supply will fit inthe case. Phil Weldon, "Mark Gross" wrote in message ... ...

Hi Pete Generally with memory timings if you go on the rule a lower value=faster performance but personally i would leave it on auto unless you want to start experiencing crashes/lockups ;-( Later. On Wed, 02 Jul 2003 14:47:00 GMT, "pete" had the will to write:

I am very interested in the Thermaltake XASER III V200A ( SILVER ) 12-Bay All Aluminum ATX Super Tower Chassis w/ L. Side Window. I would like to have a 500+ watt power supply. My question is what 500+ power supply will fit into the Thermaltake XASER III V200A ( SILVER ) 12-Bay All Aluminum ATX...

Out of curiosty, why do you have to cut power to the mobo? My mobo has a jumper that you can switch in order to clear the cmos. j/w..... -Alex "Dion L Heap" wrote in message ... "dryOtto" wrote in...

ok my motherbord is a fic az11 i have AMD Duron, 801MHz, 64KB wandering if somone could even tell me the basics on how to pump more juice out of the lil ****er.. thnx joe

This Obscene, shameful waste of our resources has Got to stop! This filth, this wanton disregard for anyone's sense of propriety. Can our Congress do nothing? Even if it is only within our own borders- are our politicians so helpless? This is a disgrace that competes with the politician's vaunted...

On Tue, 01 Jul 2003 22:18:22 GMT, "MiniDisc_2k2" wrote: Pentium 4 Northwood Rated 2.4GHz, Running at 2.95GHz @ ~45 deg C, usually a bit less System Bus @ 164Mhz VCore @ 1.675 After adding the new case fan, the temperature dropped 10 deg C. It is now stable at 35 deg C...

Hi all: This may seem to you guys a dumb question. Where do I find the FSB? I have a ASUS P4 socket A478-pin with a P4 1.4Ghz and 768 Mg SDRAM. Can somebody explain to me where to find this FSB? thanks guys. __________________________________________________________________ Gus Rosende ICQ#:...

Corsair PC3200 is rated to run at 400MHz. You are pushing it. You need PC3500@433MHz or PC3700@466MHz to run at 430MHz. -- Regards (-: Gary Hegan :-)

If I push the reset button during the BIOS loading sequence, it resets all of my overclocking scenarios. If I push mine too far it does the same thing, then when I hit reset it resets my computer back to a 133 bus and DDR400. Try turning on your computer and about 5 seconds after push reset. --...

I'm breaking in a P4 2.4 400 at default settings, with boxed fan I just purchased (costa rica 4/30/3 pack date). It's replacing an old P4 1.8A which wouldn't get much higher than 2.2 at 1.65V (I prefer keeping the Vcore low, like 1.6 or below). The 1.8A was actually drifting over time - becoming...

Like that's not a good overclock already. P4 2.4 533Fsb My Board is a Asus P4PE SoundCard Is a Creative Audigy2 I Also have a ATA Raid Card, nothing on it at the time, but it's nice to have if I get too many more hardrives. A Lynksys ethernet card. And an extra usb card. cooling if by swiftech. ...

I think somebody was asking about this a few days ago. ATI HOPS ON THE 800-MHZ BUS Integrated graphics chips will support Pentium 4's faster frontside bus. http://www.pcworld.com/news/article/0,aid,111445,tk,dn070303X,00.asp

Sometimes, when I run Outlook, AIM, or IE, my computer either doesn't connect to the server, runs really slow, or something. Could this be a result of instability after overclocking? Stats: Pentium 4 Northwood 2.4GHz @ 2.95GHz System Bus = 164MHz (standard = 133MHz) FSB = 4*164 = 656MHz 1x 256MB...

On Thu, 5 Jun 2003 21:46:56 +0200, "Régis SALEUR" wrote: Hi 1) is there a way with this MB to lock the PCI/AGP buses at 33/66MHz? Yes, "turbo mode" (the two turbo settings actually runs the buses a little faster than 33/66, forget the exact figures).

They are good PSU put not the best when you put the load and heat to them. Most PSU are rated to run at 550 Watt at 25C. When you start heating it up and pushing the PSU to 40C your max wattage will drop to about 366 Watts. You show me a PSU that runs at 25C when it is in operation. There is...

I tried to overclock my P4 2.8GHz by changing the FSB. I noticed that the frequency for AGP/PCI and memory will change together with the FSB. I am unable to just change the FSB only. How do I unlock the AGP/PCI frequency so that only the FSB is changed? If not, i can't do overclocking.

My Slot T Bios reports it as a "PIII 572B MHZ" Is this a normal report for an abit BF6 with latest bios?? Thanks

"Joop van vugt" wrote in message ... Hello ik have a proccessor pentium 4 2.4 fsb 533 Same as me. Good overclocking choice (I'll tell you why in a second). i have also 528 rimm memory (pc4200) Wow that's fast.

Hello, Based on advice from this group, I just built a system using the following: My goal was to run it at 3.0ghz (12X250). It will boot, it will post, it will do most applications okay, but when I run Medal of Honor or MS Flightsim 2000, it crashes. I either get the blue screen (lower voltages...