Just got an abit nf7-s ver 2 up and running with an xp2700 and the cpu temp sits around 50-52 idle with no overclocking compared to 39-40 in the last board I had it in, msi kt4 ultra. I replaced the thermal grease and all seems seated fine. Even with case fan blowing directly on heatsink I get no...

try taking your ram out and installing them again, and also reset the cmos. "zoeyw" wrote in message ... I have just install a new AMD 2.4+ Ghz with the Asus motherboad. Ram 512 DDR400. 40 gb Maxtor HD and 128MB of v ram. My problem is that...

Hello! I'm searching for wich PLL I've on my ASUS A7N266 to cfg CPUCool v.7.2.4 to try speed up my system over fsb @140. From bios, I can't start @142... I would try to set this value when winxp started. Thanks for any help.

My Crucial 512MB stick went bad. I am contemplating a CL, PC2700 or 3200 RAM module. I am looking at Kingston Hyper-X modules. Anyone have experience with this brand on the GA-7DXR+ from Gigabyte? I run a XP2400+, currently with ZERO overclock stability (crashes right away if I increase the FSB...

I'd be in Vegas! "James Paraskeva" wrote in message ... to put together a computer (not my money.. i go to uni) and its actually $AU6500 ... what would you do with the money? Case: XaserIII-V2000+

As above really - i have an Athlon XP1600+ in there at the moment - but i'd like to know if i can plonk a Barton 2500+ or higher in there. I know the chipset is only a lowly KT266A, but i cant afford a new board right now. Cheers.. Kai

The hard overclock has becomes easy, thanks to Wes Newell. He has linked me to: http://www.ocinside.de/go_e.html?/html/workshop/pinmod/amd_pinmod.html Now, I've unlocked the 13-13.5-14x on my Gigabyte 7VAXP with 2400+ with AIR COOLING SYSTEM. 174FSB (on KT400!) 13.5x multiplier

Hi All, I'm planning on getting the MSI Nforce board, with a barton 2500+. What do i need to do / know to overclock this beauty? I'll be running dual sata drives too.... If thats at all relevant! Cheers, Dan

which chip will give the better performance between the Thunderbird 1GHz and the Duron 1.3GHz? I am limited for choice as to what procesor I can get in my motherboard (Abit KT7) and although the best i could hope for would a 1.3GHz Thunderbird, I can't find anywhere that is still selling these. I...

Longish story short - I need to know what type of CPU I've got in my computer, and I don't really know how to go mucking around inside there (e.g. ripping out the fan). I've been told it's a 2700+, but it's showing up as a 2000+ with a 1667 clock speed, FSB set to 133MhZ. The AMD "CPU Information"...

This with the MSI K7N2 board. Overclockable or not? If so, how do ya do it?-- Michael Zentner

Anyone like to offer any opinions here? My 2600+ is running at 45C idle and that doesn't leave a lot of room for overclocking... Looking for a good heatsink and fan that'll keep it well cool, preferably from a UK retailer. Any thoughts? What are most of you using at the moment?...

I have bought a XP2600+ (FSB 333) processor and would like to overclock it on my KT3 Ultra2 board. I am using PC2700 memory. I have tried to change the multiplier from 12.5 to 14 in the bios but the system is only recognising it as a 863Mhz processor (multiplier 5x) for some reason. I don't think...

at least one fan blowing air in at the bottom/front and one fan sucking air out at the top/rear. You can see if case ventilation is a problem by running with the side off, if this drops your temp you need better ventilation and what if the temp is rising? i mean when i remove side panel,...

Make sure it's not the power supply....bring it to a tech. ASAP! -- ------------------------- Just another Democratic Slave NO more Corporate Government j wrote in message ... does anyone have the 800 number? all i can find are...

Any thoughts on 64bit computing and overclocking the new generation of chips? Just wondering what you all think about Apple's new G5 versus AMD's 64 bit offering due out for the home desktop market in September. Obviously you'd have a hard time overclocking an Apple but the new machine looks like...

I have a Barton 2500 (1833mhz) and a Nforce2 8RDA Epox MB. Latest Bios. If I try to change the multiplier from 12.5 to 13.0 and I save the changes in the BIOS and reboot. The bios reports overclocking failed. This is irrelavent of the FSB speed. Even at the lowest FSB speed a real 100mhz (without...

I am working out the details for a new system I am building. I am on a somewhat limited budget (we public college students are so poor). I already have an Asus A7N8X Deluxe mobo. I am probably going to get an AMD 2600+ Barton and 512 MB of 2700 RAM. Here are my questions: 1. Is it worth the extra...

Ozone wrote: what wes is saying ...by cutting the bridges on the cpu to default 13x multiplier....if i am followint the many threads is this. you turn a 1700+ into a 2100+ by modding the L3-3 and L3-5 bridges. your cpu will then remap some of the multipliers on your cpu.... which wes was...

On Tue, 24 Jun 2003 09:58:22 +0000, Neil wrote: Tbred B 1700 is already unlocked from the factory but not if you want a higher than 12.5 multiplier on most nf2 boards, you have to mod the chip and fool bios to enable the higher mutipliers. IE: make your 1700+ a 2100+ at default...