|
|
Could this be overclocking??? by
David Maynard
Uncle Vinnie wrote:
Thanks Dave... the odd thing is that I have the problems when I have 2 of
the 133's! If I have a 256-133 in the first slot and a 128-100 in the 2nd,
all works fine! I don't like to mix but this configuration is working... I
was thinking of asking the company to replace...
|
|
0 |
1,725 |
|
|
|
|
0 |
680 |
|
|
Power Supply Question by
S.Heenan
Mark Gross wrote:
I am very interested in the Thermaltake XASER III V200A ( SILVER )
12-Bay All Aluminum ATX Super Tower Chassis w/ L. Side Window.
I would like to have a 500+ watt power supply.
My question is what 500+ power supply will fit into the Thermaltake
XASER III V200A (...
|
|
0 |
914 |
|
|
Power Supply Question by
Phil Weldon
If the case meets ATX specifications and the power supply meets ATX
specifications, then the power supply will fit inthe case.
Phil Weldon,
"Mark Gross" wrote in
message ...
...
|
|
0 |
1,101 |
|
|
Memory timings for best speed by
Lee
Hi Pete
Generally with memory timings if you go on the rule a lower value=faster
performance but personally i would leave it on auto unless you want to
start experiencing crashes/lockups ;-(
Later.
On Wed, 02 Jul 2003 14:47:00 GMT, "pete" had the
will to write:
|
July 2nd 03 11:14 PM
by Lee
|
0 |
1,239 |
|
|
Power Supply Question by
Courseyauto
I am very interested in the Thermaltake XASER III V200A ( SILVER ) 12-Bay
All Aluminum ATX Super Tower Chassis w/ L. Side Window.
I would like to have a 500+ watt power supply.
My question is what 500+ power supply will fit into the Thermaltake XASER
III V200A ( SILVER ) 12-Bay All Aluminum ATX...
|
|
0 |
662 |
|
|
DFI's NFII Ultra motherboard - how to reset the BIOS by
MiniDisc_2k2
If I push the reset button during the BIOS loading sequence, it resets all
of my overclocking scenarios. If I push mine too far it does the same thing,
then when I hit reset it resets my computer back to a 133 bus and DDR400.
Try turning on your computer and about 5 seconds after push reset.
--...
|
|
0 |
1,183 |
|
|
ATI pumps up to 800Mhz to support P4's faster frontside. by
Chuck in Minot
I think somebody was asking about this a few days ago.
ATI HOPS ON THE 800-MHZ BUS
Integrated graphics chips will support Pentium 4's faster frontside
bus.
http://www.pcworld.com/news/article/0,aid,111445,tk,dn070303X,00.asp
|
|
0 |
631 |
|
|
O/C with ASUS P4B266 by
Joshua P. Hill
On Thu, 5 Jun 2003 21:46:56 +0200, "Régis SALEUR"
wrote:
Hi
1) is there a way with this MB to lock the PCI/AGP buses at 33/66MHz?
Yes, "turbo mode" (the two turbo settings actually runs the buses a
little faster than 33/66, forget the exact figures).
|
|
0 |
662 |
|
|
ASRock K7VT2 by
BoroLad
In article , stuart@one-
dimensional.co.uk says...
Hi all
I've been thinking of upgrading my aging Duron 900 & I've seen a good
offer for an AthlonXP2400+ & an ASRock K7VT2 MB, just wondered if anyone
had any experience with overclocking on...
|
|
0 |
713 |
|
|
xp2500+ by
raj
nice i got my 2500+ barton cor to 2.0ghz like nothing, at full load it sits
at 47c and idle 43c
|
July 1st 03 06:49 AM
by raj
|
0 |
578 |
|
|
I really don't want to drive back up to North Houston! by
MD Vid
I wouldn't want to drive in Houston under any circumstances, either.
JTH
"Strontium" wrote in message
...
It's a bad CMOS chip. The board is going back. I've cleared CMOS, till
the
cows came home. Thanks for your input, anyway.
...
|
June 23rd 03 05:29 PM
by MD Vid
|
0 |
1,880 |
|
|
Help! Cpu fan by
S.Heenan
"Fred Harnum" wrote in message
...
I'm looking for a good CPU heatsink and fan for a
P4 Socket 478
2.0a @ 2.8a
Whats good?
And where do i get one?
Thanks
|
|
0 |
1,710 |
|
|
|
June 28th 03 04:03 PM
by DEW
|
0 |
1,496 |
|
|
Great Product! Tt Spark 7 by
pete
Just installed one today on my P4 2.0. Using the manual control feature with
the fan turned down to its lowest position, the following obsversations with
stock HSF and then the Spark 7 were noted. Max load before the Spark 7 using
stock HSF temps went to 45c. To recover back to normal idle temp of...
|
June 29th 03 12:08 AM
by pete
|
0 |
999 |
|
|
Curious about memory and FSB speeds by
NightSky 421
I have a 2.26GHz Pentium 4 (SL67Y Malaysia) on an Asus P4B533 motherboard
updated to the 1014 BIOS. I also have 512MB of Infineon PC-2100 CAS Latency
2 RAM (2x256) and have owned this combo for a little over a year now. I
noticed that my processor can overclock fairly well. However, one thing...
|
|
0 |
1,186 |
|
|
|
|
0 |
1,000 |
|
|
radeon 9800 pro clock settings by
Pete Graham
I have just bought a Powercolor Radeon 9800 Pro, but the clock settings read
"n/a" in Powerstrip and Rage 3D Tweak.
How do I unlock the settings ? (If I can)
|
|
0 |
981 |
|
|
|
|
0 |
746 |
|
|
Settings for Radeon 9500 Pro (to OC it) by
Eric Bouchard
What are the best and/or safest settings to overclock a Radeon 9500 Pro?
Also, what software is the best to accomplish this? Is Rage3D a good choice?
Also, do you get additional cooling? If so, in what form?
Thanks for your help.
Eric B.
|
|
0 |
1,175 |