Hi I have just installed the motherboard and I think that Ram slots 2 & 3 may be faulty. I have two sticks of 512mb PC2100 DDR Ram that are working perfectly, they came straight from a working system this morning. They are in with an AthlonXP2400+. When I boot up my 8RDA+ with just one stick in...

That's funny but I recently transplanted an entire WinXP system from an AMD/NForce System to an Intel/Intel system without doing a dame thing. System performance was right where it should be. "Wes Newell" wrote in...

Hi It should be better.But check the 8RDA northbridge as the earlier versions (A2 and A3)had quite bad dips in the middle so either do a bit of lapping or put most of the thermal paste in the middle to fill up the dip best you can Smiffy

Thanks to Wes and TomG and all the others, I got my 2400 today and installed it with no problems, well except that i plug the keyboard in the wrong port and thought there was a problem getting into cmos. I did get the retail version but i am using the Ax-7 for the heatsink. Idle temps are 37c....

She's a tool in a Fed publicity stunt! Theyre too on the take to go after the corporate criminal Martha's toast so they look like public benefactors. -AA wrote in message

"Mattrix" wrote in message ... Wes Newell wrote: snip If you are SURE it's a tbred B core, cut L3-3 and L3-5. This will set the default multiplier to 13 (IOW, turn the cpu into a 2100+). After that it should...

On Tue, 24 Jun 2003 09:58:22 +0000, Neil wrote: Tbred B 1700 is already unlocked from the factory but not if you want a higher than 12.5 multiplier on most nf2 boards, you have to mod the chip and fool bios to enable the higher mutipliers. IE: make your 1700+ a 2100+ at default...

at least one fan blowing air in at the bottom/front and one fan sucking air out at the top/rear. You can see if case ventilation is a problem by running with the side off, if this drops your temp you need better ventilation and what if the temp is rising? i mean when i remove side panel,...

Hi All, I'm planning on getting the MSI Nforce board, with a barton 2500+. What do i need to do / know to overclock this beauty? I'll be running dual sata drives too.... If thats at all relevant! Cheers, Dan

it does. "Free" wrote in message ... Even though PM8 theoretically will convert NTFS to FAT32, I have never been able to actually do it. There seems to always be some catch, e.g. compressed files, encrypted files,...

"Minotaur" wrote in message ... It's flawed engineering! Boat motors have had this technology for years. It's called duoprop. Two props stacked together. Actually, they are counter rotating. So try to find a fan...

Hi I have just installed the motherboard and I think that Ram slots 2 & 3 may be faulty. I have two sticks of 512mb PC2100 DDR Ram that are working perfectly, they came straight from a working system this morning. They are in with an AthlonXP2400+. When I boot up my 8RDA+ with just one stick in...

1) Is there any benchmark comparing Itanium and Opteron running a 32-bit chess software? 2) Is there any benchmark comparing Itanium and Opteron running a 64-bit chess software compiled for each processor?

I just bought a JETWAY v266B mobo. The Jetway website says that it will support an AMD 2400 (with the latest BIOS ) and using a multiplier of 15 ( FSB of 133/266). OK , so far. Trouble is that the manual included with the mobo and the manual at the website only shows the switch settings for a...

3000 @ 208 FSB-11.5x = 2404mhz , Corsair @ 7,2,2,2 @ 2.8v runs great, try lower or raise multiplyer? "Rip Munsterman" wrote in message ... I just built the system listed below. I have been able to overclock the FSB to...

Thanks. On Sun, 22 Jun 2003 02:44:58 GMT, "LBJGH" wrote: Nop, the 'B' refered to the thoroughbred cpu's i.e., AIUGA is a t-bred 'A' and a JIUGB is a t-bred 'b' the stepping (AQXEA) is important and so is the date 0313, 0315, 0320, etc.

**************************************************************************** ************************** UNOS BREVES MINUTOS DE TU TIEMPO PUEDEN SIGNIFICAR LA PROSPERIDAD ESTE AÑO! **************************************************************************** ************************** Esta es una...

"David. E. Goble" wrote in message ... On Sat, 21 Jun 2003 09:32:49 -0400, "bluestringer" wrote: Bump the FSB a little. I run mine at 135. What temp should the cpu be runnning...

Arctic Silver's web site says to rub it into the heatsink with a plastic bag on your finger, then wipe all the excess off, before putting it on the cpu. -- Ed Light Smiley :-/ MS Smiley :-\

The hard overclock has becomes easy, thanks to Wes Newell. He has linked me to: http://www.ocinside.de/go_e.html?/html/workshop/pinmod/amd_pinmod.html Now, I've unlocked the 13-13.5-14x on my Gigabyte 7VAXP with 2400+ with AIR COOLING SYSTEM. 174FSB (on KT400!) 13.5x multiplier