"G©" wrote in message ... 2400xp ????????????? thanks for the help dude's G b for sure.

Solteks are doing very good on the nf2 platform, everyone seems to love them.. Neil "BK24" wrote in message ...

Hi! I have unlocked my XP2100 with the wire method and i can access the lower mult from 5X to 12.5X max. How come I cannot access the higher mult 12.5X ? Regards, David

hi, i have a amd duron 1,3. motherboard is k7sem. if i set the fbs to 133 mhz (now is 100), it will work? 2- if i set the fbs to 112 for the cpu and 112 for the ram(now ram is at 133), the ram will go slowly?

took a 2600tbred and set it to 200x12 went ok now at 218x11 tested all day in summer heat rock stable using burn in test and unreal flyby for ten hours

I have an EPOX 8rda+ main board , was wondering if the onboard sound is better quality than an Soundblaster Live card i've got kicking around? Do you recommend i use the onborad sound or shall i stick the cound card bakc in and disable the onboard audio? Comments plz

One of my systems has gotten a bit flakey so I'm going through all of the usual tests to find out what is causing the difficulties. I was suspicious of a stick of RAM. The system in question has a matched pair of CAS 2.5 256meg sticks of crucial PC-133. With two slots populated, the errors were...

Okay... I'm doing some experiments with an AMD XP3000 CPU in the Shuttle XPC (SN41G2 - NForce2) system. This has to do with FAN direction. I've yet to use the HEAT PIPE (okay, how tight is tight? Im supposed to set the wright under 4KG with an electronic screwdriver? Uh - where do I get...

just got some new ram ocz ddr platinum 256x2 I can now run my xp2600 at 12x200 to get 2400mhz on a asus a7n8x delux

i have a barton 2500 in an msi k7n2 and have 512mg of pc2700 twinmoss/mtec ddr i am only able to get it to go up to 2128mhz (11.5x 185) otherwise xp will not load. i have had it posting at just over 2.2ghz but stops when xp kicks in. ive seen reports of a very similar setup (same board, same pro,...

Don't take the subject literally... Has anybody ever tried housing the PC unit in a fridge with the usual exhaust and intake fans on the case (as well as obviously using good cooling solutions on-chip)? That should cool things down considerably, right?

Hello there I need a computer for uni (in october), but im also a gamer! if i was building now i would probably go for a 2500xp barton with a nforce ultra 400 mobo but i know its the end of the roadmap for socket A (and i dont want to another situation like my slot A lol) im just curious what i...

probably a few days too late to ask but - anybody here like to share their views on this board ?

Hi all, I have an MS-6195 slot A board. It has 3 dimm sockets. At present I have two 128MB sticks in place. If I try to put in another stick, it doesn't recognize anything above 256MB. It makes no difference which sockets I use. Iam trying to increase the memory to the max of 768MB. I have tried...

My system specs are as follows: Barton 2500+ w/ Aero 7+ Cooler NF7-S 2.0 Mobo Radeon 9600 pro (soon to be oced) WD 80gb 8mb cache hdd Can some one recommend some decent ram in this range? I hope to reach 200mhz fsb as this is the best ocing mobo on the market. I've been thinking of getting...

duah?

Hi, I just upgraded my GFX card from a GF2 Ultra to a Radeon 9700 Pro and now the PC crashes when ever the CPU load jumps to 100% while re-encoding a XviD movie using TMPG Encoder. Here`s my setup: Windows 2000 Professional Sp3 Gigabyte GA7VA ( vF9 bios )

Using retail heatsink from 3000+ barton chip, getting 65C constant, at load and idle, running on asus a7v333. Runs great, but i think it's too hot. Will try some arctic silver, but anything else to try?

I have a Chaintech Zenith Nforce board, and I just got a matching PC2700 stick to make a pair. To run dual channel, do I just stick it in the DDR3 slot and go, or are there some settings I should change? I'm still running them at 166mhz. Thanks for any tips!

I just bought an 2500xp boxed and according to the details on the chip it was 4 weeks old. doughnut "Ed" wrote in message ... The boxed parts are usually older chips (earlier stepping) and probably won't over clock as good as...