|
|
Lurker says Thanks, a Question, and a Comment by
Thom
After perusing this group for a while yesterday I am now able to stream live
video from my website using Windows Media Encoder.
There was a little trial and error involved involving my IP (behind a router
and misreported by WME) but I managed to get it sorted out.
I also ran into a little...
|
September 19th 04 08:05 PM
by Thom
|
8 |
628 |
|
|
2 Logitech Q. Cordless on the same PC by
Miqui
Is it possible to connect two or more Logitech Quickcam Cordless on
the same PC? I found that you can't connect two or more Logitech
QuickCam Pro 3000, i hope Logitech resolved this great bug.
Thanx
|
September 17th 04 12:55 PM
by Miqui
|
2 |
3,323 |
|
|
|
September 17th 04 11:57 AM
by Arek
|
0 |
625 |
|
|
DCS-5300W by
Tom Poland
Problems with web site.
After several attempts I finally got my webcam up and running on my
web page.
Now the problem I have is with the h263ctrl.cab, I have this .zip file
on my web site in the plugin folder, also in the main directory.
But when I try to open the page in a virgin browser, the file...
|
September 17th 04 08:05 AM
by Bob L
|
3 |
460 |
|
|
|
September 17th 04 07:58 AM
by Noël®
|
4 |
374 |
|
|
CMOS vs CCD chip question? by
Radio Man
I was told the only advantage that a ccd chip
has over a cmos chip is it's superior light
sensitivity. Is the resolution of a webcam
dependent on the gathering of more light?
I assumed the quality of the lens is a major
factor rather than the type of chip?
|
September 16th 04 05:51 PM
by Velvet
|
2 |
183 |
|
|
Sony TRV11E to IEEE1934 card - which cable? by
Smith
Hi,
My new Dell PC card have IEEE 1934 fireware card and I have Sony TRV11e - DV
camcarder - want to connect and use it as webcam etc.,
I am bit confused which cable to buy 4 pin or 6 pin. www.ebuyer.co.uk
confuses me..
Thanks
|
September 16th 04 03:04 PM
by Smith
|
0 |
408 |
|
|
what kind of xtra IM software for chatting by
bumtracks
If windows ... why not just run " conf " direct ip to ip ie: NetMeeting
"Karsten Jensen" wrote in message
...
No one who can help me?
On Sun, 05 Sep 2004 21:16:48 +0200, Karsten Jensen
...
|
|
3 |
386 |
|
|
DCS-5300W LINKSYS WCG-200 ROUTER by
Tom Poland
I have been haveing trouble streaming video from my DCS-5300W Camera
to my website. I' am useing the script located on the D-Link site for
doing this.
I modified the script for my IP address.
I go to my webpage to view my camera, And it work great. BUT when I
try to view my site from out side my...
|
September 15th 04 02:45 PM
by Bob L
|
2 |
578 |
|
|
Streaming Video To a webpage by
Tom Poland
Has anybody had any success streaming video from there DCS 5300 to
there web site
I have tried the java script posted on the D-Link site with no luck.
I have tried with my router address and camera address.
I can go to my site and see the video, but when I try to accuess my
site out side my router...
|
September 13th 04 09:39 PM
by Malone
|
2 |
406 |
|
|
Vicon Protocols by
David Gerard
Anybody out there have any code or raw commands or protocols for the Vicon
Surveyor 2000? Are there any Vicon owners out there at all?
Thanks Much,
David Gerard
|
|
0 |
465 |
|
|
3Com Generic Drivers? by
Radio Man
I have a 3 ComHomeConnect webcam.
Are there drivers available for this cam other than
what the manufacturer provides?
|
September 12th 04 08:59 PM
by OrcaXP
|
2 |
288 |
|
|
Water Spots on Dome by
David Gerard
Has anyone had experience with water spots (actually preventing) on dome
cameras? I have a Vicon Surveyor and after a rainstorm I get some water
spots that are annoying as the camera is not readily accessible to clean.
Have you tried Rain-X or car wax or Pledge Spray Wax or anything else that
might...
|
|
5 |
449 |
|
|
logitech pro4000 install problems by
Andy
Since downloading the xp 2 service pack and then losing everything on my
hard drive i am trying to reinstall my webcam. It gets halfway through the
install then message pops up saying 'internal error 2711 copy wme'
Help! much appreciated thankyou.
|
|
1 |
361 |
|
|
3Com HomeConnect & Yahoo by
Radio Man
I can see my streaming video on yahoo IM but
it will not allow me to use my controls. Example:
Sharpness, Color, Gamma, Shutter Speed, etc.
It allows me to use my Philips cam without any
problems but the 3Com cam is giving me a fit!
|
|
0 |
308 |
|
|
About the Philips Vesta Pro PCVC680... by
Jojo
Hi,
Did anybody try to use a "Philips Vesta Pro PCVC680" (or the 675, should be
the same) on a Windows XP SP2 ? Do I need to use the driver from Philips,
"webupdate 1.6", or something else ? Perhaps I only need to plug the camera
? (if I remenber, these drivers have some useful settings, like the...
|
September 8th 04 08:46 PM
by Jojo
|
0 |
291 |
|
|
|
|
1 |
225 |
|
|
camcorder software by
ThE SlAyEr
hi all... just installed my first firewire card ,, hooked the dv camcorder
up to it...
now all i need is software to play , any suggestions??
regards slayer
|
|
8 |
416 |
|
|
pico 2000 by
ThE SlAyEr
anybody out there using one of these cards (dvr) with the software???
im looking for an alternative to the supplied software..
4 cameras on this machine.....
thanks
regards slayer
|
|
0 |
294 |
|
|
Logitec QuickCam-Fails to connect! by
seashells
Hi Guys
Wondered if anyone had this problem.
I run Win XP on a celeron 300 and has two USB ports in side of mini tower (USB
1.0 - I believe)
Bought this cam (Logitec QuickCam) installed the software and problems begain.
Error 1904 Module C:\Progam Files\Image studio\albumact.dll
|
September 7th 04 04:58 AM
by Gotcha
|
4 |
395 |